Nie jesteś zalogowany.
Jeśli nie posiadasz konta, zarejestruj je już teraz! Pozwoli Ci ono w pełni korzystać z naszego serwisu. Spamerom dziękujemy!

Ogłoszenie

Prosimy o pomoc dla małej Julki — przekaż 1% podatku na Fundacji Dzieciom zdazyć z Pomocą.
Więcej informacji na dug.net.pl/pomagamy/.

Strony: 1

 

#1  2011-01-24 13:12:43

  mqluke - Użytkownik

mqluke
Użytkownik
Zarejestrowany: 2008-02-03
Serwis

Odczyt SMART

Witam wszystkich

Ost na mojej maszynie przy probie kopiowania zaczely sie pojawiac dziwne bledy nt dysku w konsoli. nie moglem znalesc logow nigdzie. objawialo sie tym ze system kompletnie sie odcinal. pojawialy sie tylko bledy nt SDA
postanowilem zainstalowac ten bardzo przydatny program [b]smartmontools[/b] i oto co dostalem

Kod:

Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   111   099   006    Pre-fail  Always       -       36777682
  3 Spin_Up_Time            0x0003   095   094   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       81
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       2042
  7 Seek_Error_Rate         0x000f   074   060   030    Pre-fail  Always       -       25960176661
  9 Power_On_Hours          0x0032   078   078   000    Old_age   Always       -       19771
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       108
184 Unknown_Attribute       0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Unknown_Attribute       0x0032   100   094   000    Old_age   Always       -       333
189 High_Fly_Writes         0x003a   076   076   000    Old_age   Always       -       24
190 Airflow_Temperature_Cel 0x0022   063   056   045    Old_age   Always       -       37 (Lifetime Min/Max 37/37)
194 Temperature_Celsius     0x0022   037   044   000    Old_age   Always       -       37 (0 15 0 0)
195 Hardware_ECC_Recovered  0x001a   037   030   000    Old_age   Always       -       36777682
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       5
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       5
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0

ponizej wiecej info: to dysk Seagare 500GB

Kod:

Device Model:     ST3500320NS
Serial Number:    5QM1BLLE
Firmware Version: SN04
User Capacity:    500,107,862,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   6
ATA Standard is:  ATA/ATAPI-6 T13 1410D revision 2
Local Time is:    Sun Jan 23 11:57:54 2011 GMT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

a tu reszta raporu:

Kod:

SMART Error Log Version: 1
ATA Error Count: 33 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 33 occurred at disk power-on lifetime: 19723 hours (821 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 04 9d 00 32 e0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec ff 04 9d 00 32 a0 00      08:50:39.970  IDENTIFY DEVICE
  a1 ff 01 01 00 00 a0 00      08:50:39.568  IDENTIFY PACKET DEVICE
  00 00 00 00 00 00 00 04      08:50:34.946  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      08:50:31.851  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      08:50:31.731  NOP [Abort queued commands]

Error 32 occurred at disk power-on lifetime: 19723 hours (821 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 04 9d 00 32 e0  Device Fault; Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  a1 ff 01 01 00 00 a0 00      08:50:39.568  IDENTIFY PACKET DEVICE
  00 00 00 00 00 00 00 04      08:50:34.946  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      08:50:31.851  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      08:50:31.731  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      08:50:30.939  NOP [Abort queued commands]

Error 31 occurred at disk power-on lifetime: 19723 hours (821 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 04 9d 00 32 e0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec ff 04 9d 00 32 a0 00      08:50:25.258  IDENTIFY DEVICE
  a1 ff 01 01 00 00 a0 00      08:50:24.855  IDENTIFY PACKET DEVICE
  00 00 00 00 00 00 00 04      08:50:16.182  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      08:50:13.088  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      08:50:12.968  NOP [Abort queued commands]

Error 30 occurred at disk power-on lifetime: 19723 hours (821 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 04 9d 00 32 e0  Device Fault; Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  a1 ff 01 01 00 00 a0 00      08:50:24.855  IDENTIFY PACKET DEVICE
  00 00 00 00 00 00 00 04      08:50:16.182  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      08:50:13.088  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      08:50:12.968  NOP [Abort queued commands]
  00 00 00 00 00 00 00 ff      08:50:12.176  NOP [Abort queued commands]

Error 29 occurred at disk power-on lifetime: 19723 hours (821 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 71 04 9d 00 32 e0  Device Fault; Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  a1 00 00 00 00 00 a0 02      08:46:27.298  IDENTIFY PACKET DEVICE
  ec 00 00 00 00 00 a0 02      08:46:27.290  IDENTIFY DEVICE
  00 00 00 00 00 00 00 04      08:46:27.134  NOP [Abort queued commands]
  a1 00 00 00 00 00 a0 02      08:46:22.106  IDENTIFY PACKET DEVICE
  ec 00 00 00 00 00 a0 02      08:46:22.098  IDENTIFY DEVICE

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

teraz moje pytanie jest czy ktos potrafi stwierdzic: do wymiany albo jest ok
bo mi sie wydaje ze ja tu widze bardzo niedobre odczyty :(((
prosze o pomoc bo musze szybko decyzje podjac czy kupowac nowe dyski
dzieki!!

Ostatnio edytowany przez mqluke (2011-01-24 13:13:29)

Offline

 

#2  2011-01-24 13:44:19

  raven18 - Użytkownik

raven18
Użytkownik
Skąd: /home
Zarejestrowany: 2009-01-30

Re: Odczyt SMART

ST3500320NS to jest czarna seria, wystarczy poczytać opinie, musisz jak najszybciej uaktualnić firmware do nowszej wersji, zanim dysk przestanie w ogóle widzieć w biosie, ale to i tak teraz raczej nic nie pomoże, konieczna będzie wymiana.

Windows 8.1

Offline

 

#3  2011-01-24 14:00:41

  mqluke - Użytkownik

mqluke
Użytkownik
Zarejestrowany: 2008-02-03
Serwis

Re: Odczyt SMART

wlasnie bios to tez problem zauwazylem
jak wlaczam komputer to go nie wykrywa na poczatku. zachowuje sie tak jak by za wolno sie wlaczal
musze zrobic drugi reset dopiero wtedy go zauwaza.

Offline

 

 

Strony: 1

Stopka forum

Powered by PunBB
© Copyright 2002–2005 Rickard Andersson
Nas ludzie lubią po prostu, a nie klikając w przyciski ;-)

[ Generated in 0.008 seconds, 11 queries executed ]

Informacje debugowania

Time (s) Query
0.00010 SET CHARSET latin2
0.00004 SET NAMES latin2
0.00096 SELECT u.*, g.*, o.logged FROM punbb_users AS u INNER JOIN punbb_groups AS g ON u.group_id=g.g_id LEFT JOIN punbb_online AS o ON o.ident='3.17.166.157' WHERE u.id=1
0.00091 REPLACE INTO punbb_online (user_id, ident, logged) VALUES(1, '3.17.166.157', 1732345977)
0.00043 SELECT * FROM punbb_online WHERE logged<1732345677
0.00083 SELECT topic_id FROM punbb_posts WHERE id=163168
0.00006 SELECT id FROM punbb_posts WHERE topic_id=18146 ORDER BY posted
0.00107 SELECT t.subject, t.closed, t.num_replies, t.sticky, f.id AS forum_id, f.forum_name, f.moderators, fp.post_replies, 0 FROM punbb_topics AS t INNER JOIN punbb_forums AS f ON f.id=t.forum_id LEFT JOIN punbb_forum_perms AS fp ON (fp.forum_id=f.id AND fp.group_id=3) WHERE (fp.read_forum IS NULL OR fp.read_forum=1) AND t.id=18146 AND t.moved_to IS NULL
0.00009 SELECT search_for, replace_with FROM punbb_censoring
0.00122 SELECT u.email, u.title, u.url, u.location, u.use_avatar, u.signature, u.email_setting, u.num_posts, u.registered, u.admin_note, p.id, p.poster AS username, p.poster_id, p.poster_ip, p.poster_email, p.message, p.hide_smilies, p.posted, p.edited, p.edited_by, g.g_id, g.g_user_title, o.user_id AS is_online FROM punbb_posts AS p INNER JOIN punbb_users AS u ON u.id=p.poster_id INNER JOIN punbb_groups AS g ON g.g_id=u.group_id LEFT JOIN punbb_online AS o ON (o.user_id=u.id AND o.user_id!=1 AND o.idle=0) WHERE p.topic_id=18146 ORDER BY p.id LIMIT 0,25
0.00095 UPDATE punbb_topics SET num_views=num_views+1 WHERE id=18146
Total query time: 0.00666 s