Forum Debian Users Gang

tomato · 2006-12-27 00:04:31

Witam. mam taki problem. Posiadam kartę sieciową Edimax i starownik do niej na Debiana, ale zarówno znajomość angielskiego jak i linuxa nie jest u mnie najlepsza. Nie rozumiem co mam zrobić. Wiem że należało by zacząć od nauki podstawowych komend ale potrzebuję do tego linuxa i internetu a bez tej karty nie mam dojścia do netu. Jeżeli ktoś mógłby mi pomóc ja zainstalować byłbym bardzo wdzięczny. Prosiłbym o dokładne wyjaśnienie. poniżej przedstawiam plik readme do sterownika. Dodam że mam jądro 2.6

README
*
* Ralink Tech Inc.
*
* http://www.ralinktech.com
*

=======================================================================
ModelName:
===========
rt61

=======================================================================
Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series.
Tested in Redhat 7.3 or later.

=======================================================================
Description:
=============
This is a linux device driver for Ralink RT61 a/b/g WLAN Card.

=======================================================================
Contents:
=============
./2.4x : Makefile for kernel 2.4 series
./2.6x : Makefile for kernel 2.6 series
*.c : c files
*.h : header files
Makefile.RTL865x : Makefile for big endian platform

=======================================================================
Features:
==========
This driver implements basic IEEE802.11. Infrastructure and adhoc mode with open or shared or
WPA-PSK authentication method. NONE, WEP, TKIP and AES encryption.

=======================================================================
Build Instructions:
====================
For 2.4 series kernel:
a. $tar -xvzf RT61_Linux_STA_Drv_x.x.x.x.tar.gz
go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.

b. Use 'chmod' command to change access right of following script files :
'load', 'unload', 'Configure'

c. run 'cp ../2.4x/Makefile .'
d. $make config # config build linux os version

e. $make all # compile driver source code

f. $cp RT2561.bin /etc/Wireless/RT61STA/ # copy firmware
$cp RT2561S.bin /etc/Wireless/RT61STA/
$cp RT2661.bin /etc/Wireless/RT61STA/

g. $load # load/insmod module(rt61.o)

Note: Script functionality:
load load module to kernel
unload unload module from kernel
Configure retrieve linux version

For 2.6 series kernel:
a. run 'cd STA/Module'
'cp ../2.6x/Makefile .'

b. $make all

c. $cp RT2561.bin /etc/Wireless/RT61STA/ # copy firmware
$cp RT2561S.bin /etc/Wireless/RT61STA/
$cp RT2661.bin /etc/Wireless/RT61STA/

d. run '/sbin/insmod rt61.ko' (as root)
'/sbin/ifconfig ra0 inet YOUR_IP up'

For big endian platform:
a. replace Makefile with Makefile.RTL865x

=======================================================================
CONFIGURATION:
====================
RT61 driver can be configured via following interfaces,
i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file

i) iwconfig comes with kernel.
ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details.
iii)copy configuration file "RT61STA.dat" to /etc/Wireless/RT61STA/RT61STA.dat.

Configuration File : RT61STA.dat
---------------------------------------
# Copy this file to /etc/Wireless/RT61STA/RT61STA.dat
# This file is a binary file and will be read on loading rt.o module.
#
# Use "vi -b RT61STA.dat" to modify settings according to your need.
#
# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to "0" for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPANONE"
# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"
# for more information refer to the Readme file.
#
# The word of "Default" must not be removed
Default
CountryRegion=0
CountryRegionABand=7
WirelessMode=0
SSID=AP350
NetworkType=Infra
Channel=0
AuthMode=OPEN
EncrypType=NONE
DefaultKeyID=1
Key1Type=0
Key1Str=0123456789
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
WpaPsk=abcdefghijklmnopqrstuvwxyz
TXBurst=0
PktAggregate=0
TurboRate=0
WmmCapable=0
AckPolicy1=0
AckPolicy2=0
AckPolicy3=0
AckPolicy4=0
BGProtection=0
ShortSlot=0
IEEE80211H=0
TxRate=0
RTSThreshold=2347
FragThreshold=2346
PSMode=CAM
TxPreamble=0

-----------------------------------------------
*NOTE:
WMM parameters
WmmCapable Set it as 1 to turn on WMM Qos support
AckPolicy1~4 Ack policy which support normal Ack or no Ack
(AC_BK, AC_BE, AC_VI, AC_VO)

All WMM parameters do not support iwpriv command but ˇĄWmmCapableˇ¦ˇ¦,
please store all parameter to RT61STA.dat, and restart driver.

-----------------------------------------------
syntax is 'Param'='Value' and describes below.

1. CountryRegion=value
value
0: use 1 ~ 11 Channel
1: use 1 ~ 13 Channel
2: use 10, 11 Channel
3: use 10 ~ 13 Channel
4: use 14 Channel
5: use 1 ~ 14 Channel
6: use 3 ~ 9 Channel

2. CountryRegionForABand=value
value
0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
4: use 149, 153, 157, 161, 165 Channel
5: use 149, 153, 157, 161 Channel
6: use 36, 40, 44, 48 Channel
7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel

3. SSID=value
value
0~z, 1~32 ascii characters.

4. WirelessMode=value
value
0: 11b/g mixed,
1: 11B only,
2: 11A only
3: 11a/b/g mixed
4: 11G only

5. TxRate=value
value
   0: Auto //WirelessMode=0~4
   1: 1 Mbps    //WirelessMode=0 or 1 or 3
2: 2 Mbps    //WirelessMode=0 or 1 or 3
3: 5.5 Mbps //WirelessMode=0 or 1 or 3
4: 11 Mbps //WirelessMode=0 or 1 or 3
5: 6 Mbps //WirelessMode=0 or 2 or 3 or 4
6: 9 Mbps //WirelessMode=0 or 2 or 3 or 4
7: 12 Mbps //WirelessMode=0 or 2 or 3 or 4
8: 18 Mbps //WirelessMode=0 or 2 or 3 or 4
9: 24 Mbps //WirelessMode=0 or 2 or 3 or 4
10: 36 Mbps //WirelessMode=0 or 2 or 3 or 4
11: 48 Mbps //WirelessMode=0 or 2 or 3 or 4
12: 54 Mbps //WirelessMode=0 or 2 or 3 or 4

6. Channel=value
value
1~14 depends on CountryRegion

7. BGProtection=value
value
0: Auto
1: Always on
2: Always off

8. TxPreamble=value
value
0:Preamble Long
1:Preamble Short
2:Auto

9. RTSThreshold=value
value
1~2347

10. FragThreshold=value
value
256~2346

11. TxBurst=value
value
0: Disable
1: Enable

12. NetworkType=value
value
Infra: infrastructure mode
   Adhoc: adhoc mode

13. AdhocOfdm=value
value
0: Adhere WIFI spec, the Tx MAX rate will be 11Mbps in Adhoc mode
1: Violate WIFI spec, the Tx MAX rate will be 54Mbps in Adhoc mode(b/g mixed)
2: Violate WIFI spec, the Tx MAX rate will be 54Mbps in Adhoc mode(11g only)

14. AuthMode=value
value
OPEN    For Open System
SHARED       For Shared key System
WEPAUTO
WPAPSK
WPANONE For Adhoc Security System

15. EncrypType=value
value
NONE For AuthMode=OPEN
WEP For AuthMode=OPEN or AuthMode=SHARED
TKIP For AuthMode=WPAPSK
AES For AuthMode=WPAPSK

16. DefaultKeyID=value
value
1~4

17. Key1=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd

18. Key2=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd

19. Key3=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd

20. Key4=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd

21. WPAPSK=value
value
8~63 ASCII or
64 HEX characters

22. PktAggregate=value
value
0: Disable
1: Enable when the peer supports it

23. TurboRate=value
value
0: Disable
1: Enable 72/100 Mbps whenever applicable
(Not support yet!)

24. WmmCapable=value
value
0: Disable WMM
1: Enable WMM

25. PSMode=value
value
0: CAM Constantly Awake Mode
1: Max_PSP Max Power Savings
2: Fast_PSP Power Save Mode

26. IEEE80211H=value
value
0: Disable
1: Enable Spectrum management
(This field can be enable only in A band)

MORE INFORMATION
=================================================================================
If you want for rt61 driver to auto-load at boot time:
A) choose ra0 for first RT61 WLAN card, ra1 for second RT61 WLAN card, etc.

B) create(edit) 'ifcfg-ra0' file in /etc/sysconfig/network-scripts/,
edit( or add the line) in /etc/modules.conf:
alias ra0 rt61

C) edit(create) the file /etc/sysconfig/network-scripts/ifcfg-ra0
DEVICE='ra0'
ONBOOT='yes'

NOTE:
if you use dhcp, add this line too .
BOOTPROTO='dhcp'

*D) To ease the Default Gateway setting,
add the line
GATEWAY=x.x.x.x
in /etc/sysconfig/network

GuruPL · 2006-12-27 03:06:03

jezeli masz jajko 2.6 to instalacje masz tutaj

For 2.6 series kernel:
- musisz wiedziec w jakim katalogu masz zgrane sterowniki i tam wejsc
a. run 'cd STA/Module'
'cp ../2.6x/Makefile .'

-------
b. $make all - skompiluje moduly dla twojego jajka
-------
- sam nie mam karty WLAN wiec nie wiem co to za pliki, ale jak je przekopiujesz to na pewno nie zaszkodzi :)
c.
$cp RT2561.bin /etc/Wireless/RT61STA/ # copy firmware
$cp RT2561S.bin /etc/Wireless/RT61STA/
$cp RT2661.bin /etc/Wireless/RT61STA/

----------
tutaj instalujesz/ ladujesz modul do kernela
d. run '/sbin/insmod rt61.ko' (as root)
'/sbin/ifconfig ra0 inet YOUR_IP up'
----------

For big endian platform: - tu nie mam pojecia co to jest big endian
pewnie brat ot little endiana :)
a. replace Makefile with Makefile.RTL865x

Time (s)	Query
0.00013	SET CHARSET latin2
0.00006	SET NAMES latin2
0.00139	SELECT u., g., o.logged FROM punbb_users AS u INNER JOIN punbb_groups AS g ON u.group_id=g.g_id LEFT JOIN punbb_online AS o ON o.ident='18.225.149.143' WHERE u.id=1
0.00095	UPDATE punbb_online SET logged=1716241238 WHERE ident='18.225.149.143'
0.00064	SELECT * FROM punbb_online WHERE logged<1716240938
0.00027	SELECT topic_id FROM punbb_posts WHERE id=47963
0.00126	SELECT id FROM punbb_posts WHERE topic_id=6271 ORDER BY posted
0.00075	SELECT t.subject, t.closed, t.num_replies, t.sticky, f.id AS forum_id, f.forum_name, f.moderators, fp.post_replies, 0 FROM punbb_topics AS t INNER JOIN punbb_forums AS f ON f.id=t.forum_id LEFT JOIN punbb_forum_perms AS fp ON (fp.forum_id=f.id AND fp.group_id=3) WHERE (fp.read_forum IS NULL OR fp.read_forum=1) AND t.id=6271 AND t.moved_to IS NULL
0.00007	SELECT search_for, replace_with FROM punbb_censoring
0.00147	SELECT u.email, u.title, u.url, u.location, u.use_avatar, u.signature, u.email_setting, u.num_posts, u.registered, u.admin_note, p.id, p.poster AS username, p.poster_id, p.poster_ip, p.poster_email, p.message, p.hide_smilies, p.posted, p.edited, p.edited_by, g.g_id, g.g_user_title, o.user_id AS is_online FROM punbb_posts AS p INNER JOIN punbb_users AS u ON u.id=p.poster_id INNER JOIN punbb_groups AS g ON g.g_id=u.group_id LEFT JOIN punbb_online AS o ON (o.user_id=u.id AND o.user_id!=1 AND o.idle=0) WHERE p.topic_id=6271 ORDER BY p.id LIMIT 0,25
0.00126	UPDATE punbb_topics SET num_views=num_views+1 WHERE id=6271
Total query time: 0.00825 s

Forum Debian Users Gang

Ogłoszenie

#1 2006-12-27 00:04:31

tomato - Użytkownik

sieć bezprzewodowa

#2 2006-12-27 03:06:03

GuruPL - Członek DUG

Re: sieć bezprzewodowa

Stopka forum

Informacje debugowania