Forum Debian Users Gang

   # This is an example resource file for rTorrent.
        # ~/.rtorrent.rc and enable/modify the options as needed. Remember
        # uncomment the options you wish to enable.

        # Maximum and minimum number of peers to connect
        #min_peers = 40
        #max_peers = 100

        # Same as above but for seeding completed torrents
        #min_peers_seed = 10
        #max_peers_seed = 50

        # Maximum number of simultanious uploads per torrent.
        #max_uploads = 15

        # Global upload and download rate in KiB. "0"
        #download_rate = 0
        #upload_rate = 0

        # Default directory to save the downloaded torrents.
        #directory = ./

        # Default session directory. Make sure you don't run
        # of rtorrent using the same session directory. Perhaps
        # relative path?
        #session = ./session

        # Watch a directory for new torrents, and stop
        # deleted.
        #schedule = watch_directory,5,5,load_start=./watch/*.torrent
        #schedule = untied_directory,5,5,stop_untied=

        # Close torrents when diskspace is low.
        #schedule = low_diskspace,5,60,close_low_diskspace=100M

        # Stop torrents when reaching upload ratio in percent,
        # when also reaching total upload in bytes, or
        # reaching final upload ratio in percent.
        # example: stop at ratio 2.0 with at least
        #schedule = ratio,60,60,stop_on_ratio=200,200M,2000

        # The ip address reported to the tracker.
        #ip = 127.0.0.1
        #ip = rakshasa.no

        # The ip address the listening socket and outgoing
        # bound to.
        #bind = 127.0.0.1
        #bind = rakshasa.no

        # Port range to use for listening.
        #port_range = 6890-6999

        # Start opening ports at a random position within
        #port_random = no

        # Check hash for finished torrents. Might be usefull
        # fixed that causes lack of diskspace not to
        #check_hash = no

        # Set whetever the client should try to connect
        #use_udp_trackers = yes

        # Alternative calls to bind and ip that should
        #schedule = ip_tick,0,1800,ip=rakshasa
        #schedule = bind_tick,0,1800,bind=rakshasa

        # Encryption options, set to none (default) or any
        # allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
        #
        # The example value allows incoming encrypted connections, starts
        # outgoing connections but retries with encryption if they
        # plaintext to RC4 encryption after the encrypted handshake
        #
        # encryption = allow_incoming,enable_retry,prefer_plaintext

        #
        # Do not modify the following parameters unless you
        #

        # Hash read-ahead controls how many MB to request
        # ahead. If the value is too low the
        # while if too high the kernel might not
        # pages in memory thus end up trashing.
        #hash_read_ahead = 10

        # Interval between attempts to check the hash, in
        #hash_interval = 100

        # Number of attempts to check the hash while
        # before forcing. Overworked systems might need lower values
        # decent hash checking rate.
        #hash_max_tries = 10

        # Max number of files to keep open simultaniously.
        #max_open_files = 128

        # Number of sockets to simultaneously keep open.
        #max_open_sockets = <no default>


        # Example of scheduling commands: Switch between two ip's
        # seconds.
        #schedule = "ip_tick1,5,10,ip=torretta"
        #schedule = "ip_tick2,10,10,ip=lampedusa"

        # Remove a scheduled event.
        #schedule_remove = "ip_tick1"
[/quote]

---

[url=http://s10.bitefight.pl/c.php?uid=89351]GRYZĘĘĘ[/url]