Nie jesteś zalogowany.
Jeśli nie posiadasz konta, zarejestruj je już teraz! Pozwoli Ci ono w pełni korzystać z naszego serwisu. Spamerom dziękujemy!

Ogłoszenie

Prosimy o pomoc dla małej Julki — przekaż 1% podatku na Fundacji Dzieciom zdazyć z Pomocą.
Więcej informacji na dug.net.pl/pomagamy/.

#1  2008-04-24 20:28:07

  Khamell - Użytkownik

Khamell
Użytkownik
Zarejestrowany: 2008-04-24

Problem z uruchomieniem net24

Witam. Mam debian etcha z kernelem 2.6.18-4-686. Korzystam z net24 przy pomocy modemu speedtouch 330(czarny). Kiedyś udało mi się odpalić neta na debianie, teraz minęło już trochę czasu od tamtego momentu. Siedziałem chyba z 5 godzin i nie daję rady. Najpierw ręcznie, korzystając z tego opisu:

Kod:

http://debian.linux.pl/viewtopic.php?t=2875&postdays=0&postorder=asc&start=0

. Dochodziłem do momentu ifconfig i tam nie było tego interfejsu ppp0. Potem ładowałem firmware do modemu, tak jak w tym opisie:

Kod:

http://www.linux.rk.edu.pl/w/p/neostrada-speedtouch-330/

, a także skonfigurowałem net24 korzystając z  "speedtouchconf". Net nie ruszył. Oto ostatnie informacje wypisane przez terminal na ekran(login i hasło zmieniłem, z wiadomego powodu) :

Kod:

No further user interaction is required.
Configuring SpeedTouch Driver...
Software Configuration - SUCCESS
Building SpeedTouch Driver...
Software Build - SUCCESS
Installing SpeedTouch Driver...
Software Installation - SUCCESS
Creating ppp files in /etc/ppp
You can ignore any insmod hints here...

   *** Configuration finished. Starting the connection ***

czw kwi 24 18:25:14 CEST 2008
The modem lights should start flashing for approx. 60 seconds...
You might see some messages about USBDEVFS_BULK failed - you can ignore this.
Apr 24 18:25:14 debian-kamil modem_run[6212]: modem_run version 1.3.1 started by root uid 0
czw kwi 24 18:25:56 CEST 2008
The modem_run command failed (code 250)
modem_run results:
Failed to load microcode - this is not a problem if you
have already loaded the microcode.
The microcode can only be loaded once per system boot;
We'll assume that the microcode is already loaded, and
not call this an error.
You may encounter problems, though.
If you get a message to check your password, and your
password is definitely correct, switch off the PC, disconnect the
modem for a few seconds, re-connect, switch on, remove the speedtch
module if it is loaded, and try again.
Also check for the presence of /var/run/ppp*pid - remove this file, if found.
Running : /usr/sbin/pppd call adsl
Called pppd - you should see some messages about IP addresses now...
Apr 24 18:26:06 debian-kamil pppd[6261]: pppd 2.4.4 started by root, uid 0
Apr 24 18:26:06 debian-kamil pppd[6261]: Using interface ppp0
Apr 24 18:26:06 debian-kamil pppd[6261]: Connect: ppp0 <--> /dev/pts/2
Apr 24 18:26:10 debian-kamil pppd[6261]: Remote message: permission denied
Apr 24 18:26:10 debian-kamil pppd[6261]: Connection terminated.
*********************************
* Don't seem to have connected. *
*********************************
Please check the username and password in /etc/ppp/*-secrets.
Also check the VPI/VCI in /etc/ppp/peers/adsl
Then run /etc/init.d/speedtouch start
Current settings: <mój_login@webnet24.pl> / <moje hasło> / 0 / 35
debian-kamil:/home/kamil/speedtouchconf-27-Jun-2006# cd /etc/ppp
debian-kamil:/etc/ppp# ls
alcaudsl.sys   ip-down    ip-up.d      ipv6-up    options      peers
chap-secrets   ip-down.d  ipv6-down    ipv6-up.d  options.bak  resolv.conf
chap-secrets~  ip-up      ipv6-down.d  mgmt.o     pap-secrets
debian-kamil:/etc/ppp# gedit chap-secrets

(gedit:6323): GnomeUI-WARNING **: While connecting to session manager:
Authentication Rejected, reason : None of the authentication protocols specified are supported and host-based authentication failed.
debian-kamil:/etc/ppp# gedit pap-secrets

(gedit:6332): GnomeUI-WARNING **: While connecting to session manager:
Authentication Rejected, reason : None of the authentication protocols specified are supported and host-based authentication failed.
debian-kamil:/etc/ppp# /etc/init.d/speedtouch start
Starting ADSL connection:*
debian-kamil:/etc/ppp#

.

Ostatnio edytowany przez Khamell (2008-04-24 20:33:36)

Offline

 

#2  2008-04-25 12:07:33

  Khamell - Użytkownik

Khamell
Użytkownik
Zarejestrowany: 2008-04-24

Re: Problem z uruchomieniem net24

Przepraszam za offtopic, ale poradziłem sobie już....usunąłem moduł speedtch, może to pomogło, a może po prostu debian zmienił zdanie i ruszył z netią.

Offline

 

Stopka forum

Powered by PunBB
© Copyright 2002–2005 Rickard Andersson
Możesz wyłączyć AdBlock — tu nie ma reklam ;-)

[ Generated in 0.008 seconds, 12 queries executed ]

Informacje debugowania

Time (s) Query
0.00008 SET CHARSET latin2
0.00004 SET NAMES latin2
0.00091 SELECT u.*, g.*, o.logged FROM punbb_users AS u INNER JOIN punbb_groups AS g ON u.group_id=g.g_id LEFT JOIN punbb_online AS o ON o.ident='3.133.123.162' WHERE u.id=1
0.00088 REPLACE INTO punbb_online (user_id, ident, logged) VALUES(1, '3.133.123.162', 1732352622)
0.00038 SELECT * FROM punbb_online WHERE logged<1732352322
0.00067 DELETE FROM punbb_online WHERE ident='85.208.96.193'
0.00069 SELECT topic_id FROM punbb_posts WHERE id=89433
0.00089 SELECT id FROM punbb_posts WHERE topic_id=11288 ORDER BY posted
0.00080 SELECT t.subject, t.closed, t.num_replies, t.sticky, f.id AS forum_id, f.forum_name, f.moderators, fp.post_replies, 0 FROM punbb_topics AS t INNER JOIN punbb_forums AS f ON f.id=t.forum_id LEFT JOIN punbb_forum_perms AS fp ON (fp.forum_id=f.id AND fp.group_id=3) WHERE (fp.read_forum IS NULL OR fp.read_forum=1) AND t.id=11288 AND t.moved_to IS NULL
0.00005 SELECT search_for, replace_with FROM punbb_censoring
0.00070 SELECT u.email, u.title, u.url, u.location, u.use_avatar, u.signature, u.email_setting, u.num_posts, u.registered, u.admin_note, p.id, p.poster AS username, p.poster_id, p.poster_ip, p.poster_email, p.message, p.hide_smilies, p.posted, p.edited, p.edited_by, g.g_id, g.g_user_title, o.user_id AS is_online FROM punbb_posts AS p INNER JOIN punbb_users AS u ON u.id=p.poster_id INNER JOIN punbb_groups AS g ON g.g_id=u.group_id LEFT JOIN punbb_online AS o ON (o.user_id=u.id AND o.user_id!=1 AND o.idle=0) WHERE p.topic_id=11288 ORDER BY p.id LIMIT 0,25
0.00075 UPDATE punbb_topics SET num_views=num_views+1 WHERE id=11288
Total query time: 0.00684 s