Forum Debian Users Gang

norbertc · 2015-11-14 14:21:12

Linux meduza 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt11-1+deb8u6 (2015-11-09) x86_64 GNU/Linux

Witam!
Mam następujący problem: podczas bootowania systemu wyświetla mi się
komunikat 'irq 16 nobody cared, try "irqpool" option… Disabling irq 16'
i system przydziela przerwanie 16 do ehci, ale nie uwzględnia nvidii, w
wyniku czego nvidia-detect says 'no gpu detected'. Oto listingi:

proc/interrupts:

Kod:

 16:       2774         13         14         83      93926       2621        281        289  IR-IO-APIC-fasteoi   ehci_hcd:usb3

lspci:

Kod:

00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06) (prog-if 00 [VGA controller])
    Subsystem: ASUSTeK Computer Inc. Device 177d
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 54
    Region 0: Memory at f7400000 (64-bit, non-prefetchable) [size=4M]
    Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
    Region 4: I/O ports at f000 [size=64]
    Expansion ROM at <unassigned> [disabled]
    Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
        Address: fee00018  Data: 0000
    Capabilities: [d0] Power Management version 2
        Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [a4] PCI Advanced Features
        AFCap: TP+ FLR+
        AFCtrl: FLR-
        AFStatus: TP-
    Kernel driver in use: i915

00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05) (prog-if 20 [EHCI])
    Subsystem: ASUSTeK Computer Inc. Device 177d
    Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at f7a1c000 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME-
    Capabilities: [58] Debug port: BAR=1 offset=00a0
    Capabilities: [98] PCI Advanced Features
        AFCap: TP+ FLR+
        AFCtrl: FLR-
        AFStatus: TP-
    Kernel driver in use: ehci-pci

01:00.0 3D controller: NVIDIA Corporation GM107M [GeForce GTX 860M] (rev a2)
    Subsystem: ASUSTeK Computer Inc. Device 177d
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
    Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
    Region 3: Memory at f0000000 (64-bit, prefetchable) [size=32M]
    Region 5: I/O ports at e000 [size=128]
    Expansion ROM at f7000000 [disabled] [size=512K]
    Capabilities: [60] Power Management version 3
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
        Address: 0000000000000000  Data: 0000
    Capabilities: [78] Express (v2) Endpoint, MSI 00
        DevCap:    MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
            ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
        DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
            RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+
            MaxPayload 256 bytes, MaxReadReq 512 bytes
        DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
        LnkCap:    Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us
            ClockPM+ Surprise- LLActRep- BwNot-
        LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- CommClk+
            ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
        LnkSta:    Speed 8GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        DevCap2: Completion Timeout: Range AB, TimeoutDis+, LTR+, OBFF Via message
        DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+, OBFF Disabled
        LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
             Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
             Compliance De-emphasis: -6dB
        LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete+, EqualizationPhase1+
             EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    Capabilities: [100 v1] Virtual Channel
        Caps:    LPEVC=0 RefClk=100ns PATEntryBits=1
        Arb:    Fixed- WRR32- WRR64- WRR128-
        Ctrl:    ArbSelect=Fixed
        Status:    InProgress-
        VC0:    Caps:    PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
            Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
            Ctrl:    Enable+ ID=0 ArbSelect=Fixed TC/VC=01
            Status:    NegoPending- InProgress-
    Capabilities: [250 v1] Latency Tolerance Reporting
        Max snoop latency: 71680ns
        Max no snoop latency: 71680ns
    Capabilities: [258 v1] L1 PM Substates
        L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
              PortCommonModeRestoreTime=255us PortTPowerOnTime=10us
    Capabilities: [128 v1] Power Budgeting <?>
    Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
    Capabilities: [900 v1] #19

Czy ktoś mógłby mi pomóc i napisać co zrobić i jak przypisać nvidię do
przerwania, tak aby system ją widział i nareszcie mógłbym wtedy
zainstalować sterowniki?

Any help will be appreciated.

uzytkownikubunt · 2015-11-14 15:04:52

2374

Ostatnio edytowany przez uzytkownikubunt (2016-12-01 01:27:14)

norbertc · 2015-11-15 11:31:15

Niestety opcja 'irqpoll' nie odnosi żadnego skutku.

A miałem wcześniej sida i też nie działalo, także firmware. Linux po prostu w przerwaniach nie widzi mojej nvidii.

uzytkownikubunt · 2015-11-15 11:43:29

2378

Ostatnio edytowany przez uzytkownikubunt (2016-12-01 01:27:19)

norbertc · 2015-11-15 13:27:40

Tak. Ale tu chyba chodzi o przekierowanie/udostępnienie zasobów przerwań, a ja nie wiem jak to zrobić.

uzytkownikubunt · 2015-11-15 13:56:20

2379

Ostatnio edytowany przez uzytkownikubunt (2016-12-01 01:27:21)

norbertc · 2015-11-15 14:17:27

To jest listing z bootowania systemu - może to pomoże:

Kod:

[   14.886590] nouveau  [   VBIOS][0000:01:00.0] ... appears to be valid
[   14.886594] nouveau  [   VBIOS][0000:01:00.0] using image from ACPI
[   14.886729] nouveau  [   VBIOS][0000:01:00.0] BIT signature found
[   14.886731] nouveau  [   VBIOS][0000:01:00.0] version 82.07.49.00.0f
[   14.887151] nouveau  [ DEVINIT][0000:01:00.0] adaptor not initialised
[   14.887162] nouveau  [   VBIOS][0000:01:00.0] running init tables
[   14.990601] nouveau 0000:01:00.0: irq 56 for MSI/MSI-X
[   14.990609] nouveau  [     PMC][0000:01:00.0] MSI interrupts enabled
[   14.990641] nouveau  [     PFB][0000:01:00.0] RAM type: GDDR5
[   14.990645] nouveau  [     PFB][0000:01:00.0] RAM size: 2048 MiB
[   14.990646] nouveau  [     PFB][0000:01:00.0]    ZCOMP: 0 tags
[   14.990827] nouveau E[   PIBUS][0000:01:00.0] HUB0: 0x6013d4 0x0000573f (0x1c408200)
[   14.991939] nouveau  [     CLK][0000:01:00.0] 07: core 405 MHz memory 810 MHz 
[   14.992008] nouveau  [     CLK][0000:01:00.0] 0a: core 270-1097 MHz memory 1600 MHz 
[   14.992097] nouveau  [     CLK][0000:01:00.0] 0f: core 270-1097 MHz memory 5010 MHz 
[   14.992162] nouveau  [     CLK][0000:01:00.0] --: core 405 MHz memory 810 MHz 
[   15.005047] nouveau  [  PGRAPH][0000:01:00.0] using external firmware
[   15.005061] nouveau 0000:01:00.0: firmware: failed to load nouveau/nv117_fuc409c (-2)
[   15.005087] nouveau 0000:01:00.0: Direct firmware load failed with error -2
[   15.005088] nouveau 0000:01:00.0: Falling back to user helper
[   15.005420] nouveau 0000:01:00.0: firmware: failed to load nouveau/fuc409c (-2)
[   15.005443] nouveau 0000:01:00.0: Direct firmware load failed with error -2
[   15.005444] nouveau 0000:01:00.0: Falling back to user helper
[   15.005693] nouveau E[  DEVICE][0000:01:00.0] failed to create 0x18000717, -22
[   15.005720] nouveau E[     DRM] failed to create 0x80000080, -22
[   15.006370] nouveau: probe of 0000:01:00.0 failed with error -22
[   15.042000] vboxpci: IOMMU not found (not registered)
[   15.448135] irq 16: nobody cared (try booting with the "irqpoll" option)
[   15.448163] CPU: 4 PID: 0 Comm: swapper/4 Tainted: G           O  3.16.0-4-amd64 #1 Debian 3.16.7-ckt11-1+deb8u6
[   15.448165] Hardware name: ASUSTeK COMPUTER INC. N551JM/N551JM, BIOS N551JM.204 10/06/2014
[   15.448166]  ffff8802254f36c4 ffffffff8150b4e5 ffff8802254f3600 ffffffff810bd21d
[   15.448168]  ffff8802254f3600 0000000000000010 0000000000000000 ffffffff810bd741
[   15.448170]  0000000000000000 0000000000000000 0000000000000010 0000000000000000
[   15.448172] Call Trace:
[   15.448173]  <IRQ>  [<ffffffff8150b4e5>] ? dump_stack+0x41/0x51
[   15.448182]  [<ffffffff810bd21d>] ? __report_bad_irq+0x2d/0xc0
[   15.448185]  [<ffffffff810bd741>] ? note_interrupt+0x241/0x290
[   15.448187]  [<ffffffff810baf61>] ? handle_irq_event_percpu+0xa1/0x190
[   15.448189]  [<ffffffff810bb088>] ? handle_irq_event+0x38/0x60
[   15.448192]  [<ffffffff810be283>] ? handle_fasteoi_irq+0x83/0x150
[   15.448195]  [<ffffffff810150cd>] ? handle_irq+0x1d/0x30
[   15.448197]  [<ffffffff815144d9>] ? do_IRQ+0x49/0xe0
[   15.448200]  [<ffffffff8151232d>] ? common_interrupt+0x6d/0x6d
[   15.448201]  <EOI>  [<ffffffff8108ad0d>] ? __hrtimer_start_range_ns+0x1cd/0x390
[   15.448206]  [<ffffffff813de022>] ? cpuidle_enter_state+0x52/0xc0
[   15.448208]  [<ffffffff813de018>] ? cpuidle_enter_state+0x48/0xc0
[   15.448211]  [<ffffffff810a7f78>] ? cpu_startup_entry+0x2f8/0x400
[   15.448214]  [<ffffffff81042daf>] ? start_secondary+0x20f/0x2d0
[   15.448215] handlers:
[   15.448247] [<ffffffffa002a4d0>] usb_hcd_irq [usbcore]
[   15.448266] Disabling IRQ #16

yossarian · 2015-11-15 15:09:59

Kod:

[   15.005061] nouveau 0000:01:00.0: firmware: failed to load nouveau/nv117_fuc409c (-2)
[   15.005087] nouveau 0000:01:00.0: Direct firmware load failed with error -2
[   15.005088] nouveau 0000:01:00.0: Falling back to user helper
[   15.005420] nouveau 0000:01:00.0: firmware: failed to load nouveau/fuc409c (-2)
[   15.005443] nouveau 0000:01:00.0: Direct firmware load failed with error -2
[   15.005444] nouveau 0000:01:00.0: Falling back to user helper
[   15.005693] nouveau E[  DEVICE][0000:01:00.0] failed to create 0x18000717, -22
[   15.005720] nouveau E[     DRM] failed to create 0x80000080, -22
[   15.006370] nouveau: probe of 0000:01:00.0 failed with error -22

[/quote]
Potrzebujesz firmware.

Time (s)	Query
0.00017	SET CHARSET latin2
0.00005	SET NAMES latin2
0.00109	SELECT u., g., o.logged FROM punbb_users AS u INNER JOIN punbb_groups AS g ON u.group_id=g.g_id LEFT JOIN punbb_online AS o ON o.ident='3.14.255.167' WHERE u.id=1
0.00091	REPLACE INTO punbb_online (user_id, ident, logged) VALUES(1, '3.14.255.167', 1720458523)
0.00083	SELECT * FROM punbb_online WHERE logged<1720458223
0.00127	DELETE FROM punbb_online WHERE ident='3.12.136.3'
0.00121	DELETE FROM punbb_online WHERE ident='3.135.215.53'
0.00116	DELETE FROM punbb_online WHERE ident='85.208.96.195'
0.00109	SELECT t.subject, t.closed, t.num_replies, t.sticky, f.id AS forum_id, f.forum_name, f.moderators, fp.post_replies, 0 FROM punbb_topics AS t INNER JOIN punbb_forums AS f ON f.id=t.forum_id LEFT JOIN punbb_forum_perms AS fp ON (fp.forum_id=f.id AND fp.group_id=3) WHERE (fp.read_forum IS NULL OR fp.read_forum=1) AND t.id=27898 AND t.moved_to IS NULL
0.00008	SELECT search_for, replace_with FROM punbb_censoring
0.00559	SELECT u.email, u.title, u.url, u.location, u.use_avatar, u.signature, u.email_setting, u.num_posts, u.registered, u.admin_note, p.id, p.poster AS username, p.poster_id, p.poster_ip, p.poster_email, p.message, p.hide_smilies, p.posted, p.edited, p.edited_by, g.g_id, g.g_user_title, o.user_id AS is_online FROM punbb_posts AS p INNER JOIN punbb_users AS u ON u.id=p.poster_id INNER JOIN punbb_groups AS g ON g.g_id=u.group_id LEFT JOIN punbb_online AS o ON (o.user_id=u.id AND o.user_id!=1 AND o.idle=0) WHERE p.topic_id=27898 ORDER BY p.id LIMIT 0,25
0.00131	UPDATE punbb_topics SET num_views=num_views+1 WHERE id=27898
Total query time: 0.01476 s

Forum Debian Users Gang

Ogłoszenie

#1 2015-11-14 14:21:12

norbertc - Użytkownik

irq 16 (nobody cared) i problem z nvidią

Kod:

Kod:

#2 2015-11-14 15:04:52

uzytkownikubunt - Zbanowany

Re: irq 16 (nobody cared) i problem z nvidią

#3 2015-11-15 11:31:15

norbertc - Użytkownik

Re: irq 16 (nobody cared) i problem z nvidią

#4 2015-11-15 11:43:29

uzytkownikubunt - Zbanowany

Re: irq 16 (nobody cared) i problem z nvidią

#5 2015-11-15 13:27:40

norbertc - Użytkownik

Re: irq 16 (nobody cared) i problem z nvidią

#6 2015-11-15 13:56:20

uzytkownikubunt - Zbanowany

Re: irq 16 (nobody cared) i problem z nvidią

#7 2015-11-15 14:17:27

norbertc - Użytkownik

Re: irq 16 (nobody cared) i problem z nvidią

Kod:

#8 2015-11-15 15:09:59

yossarian - Szczawiożerca

Re: irq 16 (nobody cared) i problem z nvidią

Kod:

#9 2015-11-15 15:26:33

Jacekalex - Podobno człowiek...;)

Re: irq 16 (nobody cared) i problem z nvidią

Kod:

#10 2015-11-16 11:17:12

norbertc - Użytkownik

Re: irq 16 (nobody cared) i problem z nvidią

#11 2015-11-16 13:57:26

uzytkownikubunt - Zbanowany

Re: irq 16 (nobody cared) i problem z nvidią

#12 2015-11-16 14:25:30

norbertc - Użytkownik

Re: irq 16 (nobody cared) i problem z nvidią

#13 2015-11-16 15:00:13

uzytkownikubunt - Zbanowany

Re: irq 16 (nobody cared) i problem z nvidią

#14 2015-11-16 16:01:53

yossarian - Szczawiożerca

Re: irq 16 (nobody cared) i problem z nvidią

#15 2015-11-17 10:59:31

norbertc - Użytkownik

Re: irq 16 (nobody cared) i problem z nvidią

#16 2015-11-17 12:02:19

norbertc - Użytkownik

Re: irq 16 (nobody cared) i problem z nvidią

Kod:

#17 2015-11-17 14:31:17

norbertc - Użytkownik

Re: irq 16 (nobody cared) i problem z nvidią

#18 2015-11-17 14:38:56

uzytkownikubunt - Zbanowany

Re: irq 16 (nobody cared) i problem z nvidią

#19 2015-11-17 17:36:53

Jacekalex - Podobno człowiek...;)

Re: irq 16 (nobody cared) i problem z nvidią

#20 2015-11-17 17:43:10

ArnVaker - Kapelusznik

Re: irq 16 (nobody cared) i problem z nvidią

Stopka forum

Informacje debugowania