Forum Debian Users Gang

yomal79 · 2012-04-23 08:00:54

Witam Mam problem z rozdzielczością na zintegrowanej grafice intel Domyślnie jest 1024x768 i można ustawić tylko mniejszą
Monitor jaki mam 1440x900 Wcześniej nie miałem takiego problemu pod nvidia Nawet była możliwość wydania polecenia nvidia-xconfig które generowało plik xorg.conf
Proszę o pomoc jak to ustawić Najfajniejsze jest to że akceleracja działa z palca a próby generowania modeline dla mojego monitora kończyły się tylko możliwością wyboru innej rozdzielczości ale wcale jej nie ustawiały Ręce opadły :(

System Debian wheezy 32bit kernel nie zmieniany

Poniżej wynik lspci

Kod:

00:00.0 Host bridge: Intel Corporation Sandy Bridge DRAM Controller (rev 09)
00:02.0 VGA compatible controller: Intel Corporation Sandy Bridge Integrated Graphics Controller (rev 09)
00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04)
00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 05)
00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05)
00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5)
00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation Cougar Point LPC Controller (rev 05)
00:1f.2 IDE interface: Intel Corporation Cougar Point 4 port SATA IDE Controller (rev 05)
00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05)
00:1f.5 IDE interface: Intel Corporation Cougar Point 2 port SATA IDE Controller (rev 05)
01:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
02:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)

i jeszcze lsmod

Kod:

xt_tcpudp               1743  2
ipt_MASQUERADE          1134  1
xt_state                 927  3
iptable_mangle          2325  0
iptable_nat             3519  1
nf_nat                 10468  2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4       7597  6 iptable_nat,nf_nat
nf_conntrack           37871  5 ipt_MASQUERADE,xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4           779  1 nf_conntrack_ipv4
iptable_filter          1790  1
ip_tables               7706  3 iptable_mangle,iptable_nat,iptable_filter
x_tables                8327  5 xt_tcpudp,ipt_MASQUERADE,xt_state,iptable_nat,ip_tables
aes_i586                6816  2
aes_generic            25738  1 aes_i586
loop                    9733  0
snd_hda_codec_realtek   163378  0
arc4                     974  2
ecb                     1405  2
ath9k                 238197  0
mac80211              122874  1 ath9k
ath                     5986  1 ath9k
cfg80211               86965  3 ath9k,mac80211,ath
rfkill                 10196  1 cfg80211
led_class               1757  1 ath9k
evdev                   5609  2
snd_hda_intel          16791  0
snd_usb_audio          50634  0
i2c_i801                6462  0
psmouse                44777  0
serio_raw               2916  0
pcspkr                  1207  0
snd_hda_codec          46002  2 snd_hda_codec_realtek,snd_hda_intel
snd_pcm                47226  3 snd_hda_intel,snd_usb_audio,snd_hda_codec
uvcvideo               45574  0
videodev               25537  1 uvcvideo
v4l1_compat            10250  2 uvcvideo,videodev
i2c_core               12751  2 i2c_i801,videodev
snd_usb_lib            11156  1 snd_usb_audio
snd_seq_midi            3576  0
snd_seq_midi_event      3684  1 snd_seq_midi
snd_seq                35327  2 snd_seq_midi,snd_seq_midi_event
video                  14605  0
output                  1204  1 video
button                  3598  0
snd_rawmidi            12513  2 snd_usb_lib,snd_seq_midi
processor              26259  2
wmi                     3575  0
snd_timer              12270  2 snd_pcm,snd_seq
snd_hwdep               4054  2 snd_usb_audio,snd_hda_codec
snd_seq_device          3673  3 snd_seq_midi,snd_seq,snd_rawmidi
snd                    34387  10 snd_hda_codec_realtek,snd_hda_intel,snd_usb_audio,snd_hda_codec,snd_pcm,snd_seq,snd_rawmidi,snd_timer,snd_hwdep,snd_seq_device
soundcore               3450  1 snd
snd_page_alloc          4977  2 snd_hda_intel,snd_pcm
ext4                  256328  1
mbcache                 3762  1 ext4
jbd2                   55995  1 ext4
crc16                   1027  1 ext4
sd_mod                 25945  2
crc_t10dif              1012  1 sd_mod
ata_generic             2247  0
xhci                   29421  0
ehci_hcd               28449  0
ata_piix               17704  1
thermal                 9206  0
thermal_sys             9378  3 video,processor,thermal
usbcore                99125  6 snd_usb_audio,uvcvideo,snd_usb_lib,xhci,ehci_hcd
nls_base                4541  1 usbcore
libata                115649  2 ata_generic,ata_piix
scsi_mod              104765  2 sd_mod,libata
e1000e                110066  0

Próbowalem tym sposobem ale nie robi :( [url]http://forum.dug.net.pl/viewtopic.php?id=16258[/url]

Ostatnio edytowany przez yomal79 (2012-04-23 09:46:24)

mati75 · 2012-04-23 11:54:56

Kod:

apt-get install xserver-xorg-video-intel libdrm-intel1

yomal79 · 2012-04-23 12:24:31

Dzięki za zainteresowanie :)
Sprawdzę wieczorem Z tym xorg.conf to teraz jakieś problemy są Podczas generowania X -configure

EDIT : Tak jak myślałem Te pakiety mam zainstalowane a podczas generowania X -configure mam failed

Kod:

(++) Using config file: "/root/xorg.conf.new"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
Number of created screens does not match number of detected devices.
Configuration failed.
Server terminated witch error (2). Closing log file.

Ostatnio edytowany przez yomal79 (2012-04-23 21:12:05)

yomal79 · 2012-04-23 21:16:48

Tak wygląda xorg.conf.new

Kod:

Section "ServerLayout"
    Identifier     "X.org Configured"
    Screen      0  "Screen0" 0 0
    Screen      1  "Screen1" RightOf "Screen0"
    Screen      2  "Screen2" RightOf "Screen1"
    InputDevice    "Mouse0" "CorePointer"
    InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
    ModulePath   "/usr/lib/xorg/modules"
    FontPath     "/usr/share/fonts/X11/misc"
    FontPath     "/usr/share/fonts/X11/cyrillic"
    FontPath     "/usr/share/fonts/X11/100dpi/:unscaled"
    FontPath     "/usr/share/fonts/X11/75dpi/:unscaled"
    FontPath     "/usr/share/fonts/X11/Type1"
    FontPath     "/usr/share/fonts/X11/100dpi"
    FontPath     "/usr/share/fonts/X11/75dpi"
    FontPath     "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
    FontPath     "built-ins"
EndSection

Section "Module"
    Load  "dri2"
    Load  "extmod"
    Load  "dbe"
    Load  "dri"
    Load  "glx"
    Load  "record"
EndSection

Section "InputDevice"
    Identifier  "Keyboard0"
    Driver      "kbd"
EndSection

Section "InputDevice"
    Identifier  "Mouse0"
    Driver      "mouse"
    Option        "Protocol" "auto"
    Option        "Device" "/dev/input/mice"
    Option        "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
    Identifier   "Monitor0"
    VendorName   "Monitor Vendor"
    ModelName    "Monitor Model"
EndSection

Section "Monitor"
    Identifier   "Monitor1"
    VendorName   "Monitor Vendor"
    ModelName    "Monitor Model"
EndSection

Section "Monitor"
    Identifier   "Monitor2"
    VendorName   "Monitor Vendor"
    ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
        ### <percent>: "<f>%"
        ### [arg]: arg optional
        #Option     "DRI"                    # [<bool>]
        #Option     "ColorKey"               # <i>
        #Option     "VideoKey"               # <i>
        #Option     "FallbackDebug"          # [<bool>]
        #Option     "Tiling"                 # [<bool>]
        #Option     "LinearFramebuffer"      # [<bool>]
        #Option     "Shadow"                 # [<bool>]
        #Option     "SwapbuffersWait"        # [<bool>]
        #Option     "TripleBuffer"           # [<bool>]
        #Option     "XvMC"                   # [<bool>]
        #Option     "XvPreferOverlay"        # [<bool>]
        #Option     "DebugFlushBatches"      # [<bool>]
        #Option     "DebugFlushCaches"       # [<bool>]
        #Option     "DebugWait"              # [<bool>]
        #Option     "HotPlug"                # [<bool>]
        #Option     "RelaxedFencing"         # [<bool>]
        #Option     "BufferCache"            # [<bool>]
    Identifier  "Card0"
    Driver      "intel"
    BusID       "PCI:0:2:0"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
        ### <percent>: "<f>%"
        ### [arg]: arg optional
        #Option     "ShadowFB"               # [<bool>]
        #Option     "Rotate"                 # <str>
        #Option     "fbdev"                  # <str>
        #Option     "debug"                  # [<bool>]
    Identifier  "Card1"
    Driver      "fbdev"
    BusID       "PCI:0:2:0"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
        ### <percent>: "<f>%"
        ### [arg]: arg optional
        #Option     "ShadowFB"               # [<bool>]
        #Option     "DefaultRefresh"         # [<bool>]
        #Option     "ModeSetClearScreen"     # [<bool>]
    Identifier  "Card2"
    Driver      "vesa"
    BusID       "PCI:0:2:0"
EndSection

Section "Screen"
    Identifier "Screen0"
    Device     "Card0"
    Monitor    "Monitor0"
    SubSection "Display"
        Viewport   0 0
        Depth     1
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

Section "Screen"
    Identifier "Screen1"
    Device     "Card1"
    Monitor    "Monitor1"
    SubSection "Display"
        Viewport   0 0
        Depth     1
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

Section "Screen"
    Identifier "Screen2"
    Device     "Card2"
    Monitor    "Monitor2"
    SubSection "Display"
        Viewport   0 0
        Depth     1
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     4
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     8
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     15
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

ArnVaker · 2012-04-23 21:38:43

A bez xorg.conf? Poza tym /var/log/Xorg.0.log zazwyczaj w podobnych przypadkach się przydaje.

yomal79 · 2012-04-23 21:41:53

Kod:

[   137.104] 
X.Org X Server 1.11.4
Release Date: 2012-01-27
[   137.104] X Protocol Version 11, Revision 0
[   137.104] Build Operating System: Linux 2.6.32-5-amd64 i686 Debian
[   137.104] Current Operating System: Linux linux 3.2.0-2-686-pae #1 SMP Sun Apr 15 17:56:31 UTC 2012 i686
[   137.104] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-2-686-pae root=UUID=f2f0fd28-3d8c-45c6-b708-0decc970cb7c ro quiet
[   137.104] Build Date: 05 March 2012  04:16:09AM
[   137.104] xorg-server 2:1.11.4-1 (Cyril Brulebois <kibi@debian.org>) 
[   137.104] Current version of pixman: 0.24.4
[   137.104]     Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
[   137.104] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[   137.104] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Apr 23 21:29:42 2012
[   137.104] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[   137.105] (==) No Layout section.  Using the first Screen section.
[   137.105] (==) No screen section available. Using defaults.
[   137.105] (**) |-->Screen "Default Screen Section" (0)
[   137.105] (**) |   |-->Monitor "<default monitor>"
[   137.105] (==) No monitor specified for screen "Default Screen Section".
    Using a default monitor configuration.
[   137.105] (==) Automatically adding devices
[   137.105] (==) Automatically enabling devices
[   137.105] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[   137.105]     Entry deleted from font path.
[   137.105] (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
[   137.105]     Entry deleted from font path.
[   137.105] (==) FontPath set to:
    /usr/share/fonts/X11/misc,
    /usr/share/fonts/X11/100dpi/:unscaled,
    /usr/share/fonts/X11/75dpi/:unscaled,
    /usr/share/fonts/X11/Type1,
    /usr/share/fonts/X11/100dpi,
    /usr/share/fonts/X11/75dpi,
    built-ins
[   137.105] (==) ModulePath set to "/usr/lib/xorg/modules"
[   137.105] (II) The server relies on udev to provide the list of input devices.
    If no devices become available, reconfigure udev or disable AutoAddDevices.
[   137.105] (II) Loader magic: 0xb7704580
[   137.105] (II) Module ABI versions:
[   137.105]     X.Org ANSI C Emulation: 0.4
[   137.105]     X.Org Video Driver: 11.0
[   137.105]     X.Org XInput driver : 13.0
[   137.105]     X.Org Server Extension : 6.0
[   137.105] (--) PCI:*(0:0:2:0) 8086:0102:8086:2013 rev 9, Mem @ 0xfe000000/4194304, 0xe0000000/268435456, I/O @ 0x0000f000/64
[   137.105] (II) Open ACPI successful (/var/run/acpid.socket)
[   137.105] (II) LoadModule: "extmod"
[   137.106] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[   137.106] (II) Module extmod: vendor="X.Org Foundation"
[   137.106]     compiled for 1.11.4, module version = 1.0.0
[   137.106]     Module class: X.Org Server Extension
[   137.106]     ABI class: X.Org Server Extension, version 6.0
[   137.106] (II) Loading extension SELinux
[   137.106] (II) Loading extension MIT-SCREEN-SAVER
[   137.106] (II) Loading extension XFree86-VidModeExtension
[   137.106] (II) Loading extension XFree86-DGA
[   137.106] (II) Loading extension DPMS
[   137.106] (II) Loading extension XVideo
[   137.106] (II) Loading extension XVideo-MotionCompensation
[   137.106] (II) Loading extension X-Resource
[   137.106] (II) LoadModule: "dbe"
[   137.106] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[   137.106] (II) Module dbe: vendor="X.Org Foundation"
[   137.106]     compiled for 1.11.4, module version = 1.0.0
[   137.106]     Module class: X.Org Server Extension
[   137.106]     ABI class: X.Org Server Extension, version 6.0
[   137.106] (II) Loading extension DOUBLE-BUFFER
[   137.106] (II) LoadModule: "glx"
[   137.106] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[   137.106] (II) Module glx: vendor="X.Org Foundation"
[   137.106]     compiled for 1.11.4, module version = 1.0.0
[   137.106]     ABI class: X.Org Server Extension, version 6.0
[   137.106] (==) AIGLX enabled
[   137.106] (II) Loading extension GLX
[   137.106] (II) LoadModule: "record"
[   137.106] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[   137.106] (II) Module record: vendor="X.Org Foundation"
[   137.106]     compiled for 1.11.4, module version = 1.13.0
[   137.106]     Module class: X.Org Server Extension
[   137.106]     ABI class: X.Org Server Extension, version 6.0
[   137.106] (II) Loading extension RECORD
[   137.106] (II) LoadModule: "dri"
[   137.106] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[   137.106] (II) Module dri: vendor="X.Org Foundation"
[   137.106]     compiled for 1.11.4, module version = 1.0.0
[   137.106]     ABI class: X.Org Server Extension, version 6.0
[   137.106] (II) Loading extension XFree86-DRI
[   137.106] (II) LoadModule: "dri2"
[   137.106] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[   137.107] (II) Module dri2: vendor="X.Org Foundation"
[   137.107]     compiled for 1.11.4, module version = 1.2.0
[   137.107]     ABI class: X.Org Server Extension, version 6.0
[   137.107] (II) Loading extension DRI2
[   137.107] (==) Matched intel as autoconfigured driver 0
[   137.107] (==) Matched vesa as autoconfigured driver 1
[   137.107] (==) Matched fbdev as autoconfigured driver 2
[   137.107] (==) Assigned the driver to the xf86ConfigLayout
[   137.107] (II) LoadModule: "intel"
[   137.107] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[   137.107] (II) Module intel: vendor="X.Org Foundation"
[   137.107]     compiled for 1.11.4, module version = 2.18.0
[   137.107]     Module class: X.Org Video Driver
[   137.107]     ABI class: X.Org Video Driver, version 11.0
[   137.107] (II) LoadModule: "vesa"
[   137.107] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[   137.107] (II) Module vesa: vendor="X.Org Foundation"
[   137.107]     compiled for 1.11.4, module version = 2.3.1
[   137.107]     Module class: X.Org Video Driver
[   137.107]     ABI class: X.Org Video Driver, version 11.0
[   137.107] (II) LoadModule: "fbdev"
[   137.107] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[   137.107] (II) Module fbdev: vendor="X.Org Foundation"
[   137.107]     compiled for 1.11.0, module version = 0.4.2
[   137.107]     ABI class: X.Org Video Driver, version 11.0
[   137.107] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
    i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
    E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
    965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
    4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
    Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
    Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
    Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
    Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
    Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server
[   137.108] (II) VESA: driver for VESA chipsets: vesa
[   137.108] (II) FBDEV: driver for framebuffer: fbdev
[   137.108] (++) using VT number 7

[   137.109] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[   137.109] (WW) Falling back to old probe method for vesa
[   137.109] (WW) Falling back to old probe method for fbdev
[   137.109] (II) Loading sub module "fbdevhw"
[   137.109] (II) LoadModule: "fbdevhw"
[   137.109] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[   137.109] (II) Module fbdevhw: vendor="X.Org Foundation"
[   137.109]     compiled for 1.11.4, module version = 0.0.2
[   137.109]     ABI class: X.Org Video Driver, version 11.0
[   137.109] drmOpenDevice: node name is /dev/dri/card0
[   137.109] drmOpenDevice: open result is 9, (OK)
[   137.109] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[   137.109] drmOpenDevice: node name is /dev/dri/card0
[   137.109] drmOpenDevice: open result is 9, (OK)
[   137.109] drmOpenByBusid: drmOpenMinor returns 9
[   137.109] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[   137.109] (II) intel(0): Creating default Display subsection in Screen section
    "Default Screen Section" for depth/fbbpp 24/32
[   137.109] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[   137.109] (==) intel(0): RGB weight 888
[   137.109] (==) intel(0): Default visual is TrueColor
[   137.109] (II) intel(0): Integrated Graphics Chipset: Intel(R) Sandybridge Desktop (GT1)
[   137.109] (--) intel(0): Chipset: "Sandybridge Desktop (GT1)"
[   137.109] (**) intel(0): Relaxed fencing enabled
[   137.109] (**) intel(0): Wait on SwapBuffers? enabled
[   137.109] (**) intel(0): Triple buffering? enabled
[   137.109] (**) intel(0): Framebuffer tiled
[   137.109] (**) intel(0): Pixmaps tiled
[   137.109] (**) intel(0): 3D buffers tiled
[   137.109] (**) intel(0): SwapBuffers wait enabled
[   137.109] (==) intel(0): video overlay key set to 0x101fe
[   137.428] (II) intel(0): Output VGA1 has no monitor section
[   137.552] (II) intel(0): Output HDMI1 has no monitor section
[   137.600] (II) intel(0): Output DP1 has no monitor section
[   137.623] (II) intel(0): Output HDMI2 has no monitor section
[   138.260] (II) intel(0): Output HDMI3 has no monitor section
[   138.308] (II) intel(0): Output DP2 has no monitor section
[   138.313] (II) intel(0): Output DP3 has no monitor section
[   138.632] (II) intel(0): EDID for output VGA1
[   138.632] (II) intel(0): Printing probed modes for output VGA1
[   138.632] (II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
[   138.632] (II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
[   138.632] (II) intel(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
[   138.632] (II) intel(0): Modeline "848x480"x60.0   33.75  848 864 976 1088  480 486 494 517 +hsync +vsync (31.0 kHz)
[   138.632] (II) intel(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 489 492 525 -hsync -vsync (31.5 kHz)
[   138.756] (II) intel(0): EDID for output HDMI1
[   138.804] (II) intel(0): EDID for output DP1
[   138.827] (II) intel(0): EDID for output HDMI2
[   139.464] (II) intel(0): EDID for output HDMI3
[   139.512] (II) intel(0): EDID for output DP2
[   139.517] (II) intel(0): EDID for output DP3
[   139.517] (II) intel(0): Printing probed modes for output DP3
[   139.517] (II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
[   139.517] (II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
[   139.517] (II) intel(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
[   139.517] (II) intel(0): Modeline "848x480"x60.0   33.75  848 864 976 1088  480 486 494 517 +hsync +vsync (31.0 kHz)
[   139.517] (II) intel(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 489 492 525 -hsync -vsync (31.5 kHz)
[   139.517] (II) intel(0): Output VGA1 connected
[   139.517] (II) intel(0): Output HDMI1 disconnected
[   139.517] (II) intel(0): Output DP1 disconnected
[   139.517] (II) intel(0): Output HDMI2 disconnected
[   139.517] (II) intel(0): Output HDMI3 disconnected
[   139.517] (II) intel(0): Output DP2 disconnected
[   139.517] (II) intel(0): Output DP3 connected
[   139.517] (II) intel(0): Using fuzzy aspect match for initial modes
[   139.517] (II) intel(0): Output VGA1 using initial mode 1024x768
[   139.517] (II) intel(0): Output DP3 using initial mode 1024x768
[   139.517] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[   139.517] (II) intel(0): Kernel page flipping support detected, enabling
[   139.517] (==) intel(0): DPI set to (96, 96)
[   139.517] (II) Loading sub module "fb"
[   139.517] (II) LoadModule: "fb"
[   139.517] (II) Loading /usr/lib/xorg/modules/libfb.so
[   139.517] (II) Module fb: vendor="X.Org Foundation"
[   139.517]     compiled for 1.11.4, module version = 1.0.0
[   139.517]     ABI class: X.Org ANSI C Emulation, version 0.4
[   139.517] (II) Loading sub module "dri2"
[   139.517] (II) LoadModule: "dri2"
[   139.517] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[   139.517] (II) Module dri2: vendor="X.Org Foundation"
[   139.517]     compiled for 1.11.4, module version = 1.2.0
[   139.517]     ABI class: X.Org Server Extension, version 6.0
[   139.517] (II) UnloadModule: "vesa"
[   139.517] (II) Unloading vesa
[   139.517] (II) UnloadModule: "fbdev"
[   139.517] (II) Unloading fbdev
[   139.518] (II) UnloadModule: "fbdevhw"
[   139.518] (II) Unloading fbdevhw
[   139.518] (==) Depth 24 pixmap format is 32 bpp
[   139.518] (II) intel(0): [DRI2] Setup complete
[   139.518] (II) intel(0): [DRI2]   DRI driver: i965
[   139.518] (II) intel(0): Allocated new frame buffer 1024x768 stride 4096, tiled
[   139.518] (II) UXA(0): Driver registered support for the following operations:
[   139.518] (II)         solid
[   139.518] (II)         copy
[   139.518] (II)         composite (RENDER acceleration)
[   139.518] (II)         put_image
[   139.518] (II)         get_image
[   139.518] (==) intel(0): Backing store disabled
[   139.518] (==) intel(0): Silken mouse enabled
[   139.518] (II) intel(0): Initializing HW Cursor
[   139.632] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[   139.632] (==) intel(0): DPMS enabled
[   139.632] (==) intel(0): Intel XvMC decoder enabled
[   139.632] (II) intel(0): Set up textured video
[   139.632] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[   139.632] (II) intel(0): direct rendering: DRI2 Enabled
[   139.632] (==) intel(0): hotplug detection: "enabled"
[   139.632] (--) RandR disabled
[   139.632] (II) Initializing built-in extension Generic Event Extension
[   139.632] (II) Initializing built-in extension SHAPE
[   139.632] (II) Initializing built-in extension MIT-SHM
[   139.632] (II) Initializing built-in extension XInputExtension
[   139.632] (II) Initializing built-in extension XTEST
[   139.632] (II) Initializing built-in extension BIG-REQUESTS
[   139.632] (II) Initializing built-in extension SYNC
[   139.632] (II) Initializing built-in extension XKEYBOARD
[   139.632] (II) Initializing built-in extension XC-MISC
[   139.632] (II) Initializing built-in extension SECURITY
[   139.632] (II) Initializing built-in extension XINERAMA
[   139.632] (II) Initializing built-in extension XFIXES
[   139.632] (II) Initializing built-in extension RENDER
[   139.632] (II) Initializing built-in extension RANDR
[   139.632] (II) Initializing built-in extension COMPOSITE
[   139.632] (II) Initializing built-in extension DAMAGE
[   139.632] (II) SELinux: Disabled on system
[   139.640] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[   139.640] (II) AIGLX: enabled GLX_INTEL_swap_event
[   139.640] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[   139.640] (II) AIGLX: enabled GLX_SGI_make_current_read
[   139.640] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[   139.640] (II) AIGLX: Loaded and initialized i965
[   139.640] (II) GLX: Initialized DRI2 GL provider for screen 0
[   139.641] (II) intel(0): Setting screen physical size to 270 x 203
[   139.667] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[   139.667] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[   139.667] (II) LoadModule: "evdev"
[   139.667] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   139.667] (II) Module evdev: vendor="X.Org Foundation"
[   139.667]     compiled for 1.11.4, module version = 2.7.0
[   139.667]     Module class: X.Org XInput Driver
[   139.667]     ABI class: X.Org XInput driver, version 13.0
[   139.667] (II) Using input driver 'evdev' for 'Power Button'
[   139.667] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   139.667] (**) Power Button: always reports core events
[   139.667] (**) evdev: Power Button: Device: "/dev/input/event1"
[   139.667] (--) evdev: Power Button: Vendor 0 Product 0x1
[   139.668] (--) evdev: Power Button: Found keys
[   139.668] (II) evdev: Power Button: Configuring as keyboard
[   139.668] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1"
[   139.668] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[   139.668] (**) Option "xkb_rules" "evdev"
[   139.668] (**) Option "xkb_model" "pc105"
[   139.668] (**) Option "xkb_layout" "pl"
[   139.682] (II) config/udev: Adding input device Video Bus (/dev/input/event7)
[   139.682] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[   139.682] (II) Using input driver 'evdev' for 'Video Bus'
[   139.682] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   139.682] (**) Video Bus: always reports core events
[   139.682] (**) evdev: Video Bus: Device: "/dev/input/event7"
[   139.682] (--) evdev: Video Bus: Vendor 0 Product 0x6
[   139.682] (--) evdev: Video Bus: Found keys
[   139.682] (II) evdev: Video Bus: Configuring as keyboard
[   139.682] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input7/event7"
[   139.682] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[   139.682] (**) Option "xkb_rules" "evdev"
[   139.682] (**) Option "xkb_model" "pc105"
[   139.682] (**) Option "xkb_layout" "pl"
[   139.683] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[   139.683] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[   139.683] (II) Using input driver 'evdev' for 'Power Button'
[   139.683] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   139.683] (**) Power Button: always reports core events
[   139.683] (**) evdev: Power Button: Device: "/dev/input/event0"
[   139.683] (--) evdev: Power Button: Vendor 0 Product 0x1
[   139.683] (--) evdev: Power Button: Found keys
[   139.683] (II) evdev: Power Button: Configuring as keyboard
[   139.683] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0/event0"
[   139.683] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[   139.683] (**) Option "xkb_rules" "evdev"
[   139.683] (**) Option "xkb_model" "pc105"
[   139.683] (**) Option "xkb_layout" "pl"
[   139.683] (II) config/udev: Adding input device A..... G3 (/dev/input/event3)
[   139.683] (**) A..... G3: Applying InputClass "evdev pointer catchall"
[   139.683] (II) Using input driver 'evdev' for 'A..... G3'
[   139.683] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   139.683] (**) A..... G3: always reports core events
[   139.683] (**) evdev: A..... G3: Device: "/dev/input/event3"
[   139.683] (--) evdev: A..... G3: Vendor 0xe0ff Product 0x2
[   139.683] (--) evdev: A..... G3: Found 12 mouse buttons
[   139.684] (--) evdev: A..... G3: Found scroll wheel(s)
[   139.684] (--) evdev: A..... G3: Found relative axes
[   139.684] (--) evdev: A..... G3: Found x and y relative axes
[   139.684] (II) evdev: A..... G3: Configuring as mouse
[   139.684] (II) evdev: A..... G3: Adding scrollwheel support
[   139.684] (**) evdev: A..... G3: YAxisMapping: buttons 4 and 5
[   139.684] (**) evdev: A..... G3: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[   139.684] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.1/3-1.1:1.0/input/input3/event3"
[   139.684] (II) XINPUT: Adding extended input device "A..... G3" (type: MOUSE, id 9)
[   139.684] (II) evdev: A..... G3: initialized for relative axes.
[   139.684] (**) A..... G3: (accel) keeping acceleration scheme 1
[   139.684] (**) A..... G3: (accel) acceleration profile 0
[   139.684] (**) A..... G3: (accel) acceleration factor: 2.000
[   139.684] (**) A..... G3: (accel) acceleration threshold: 4
[   139.684] (II) config/udev: Adding input device A..... G3 (/dev/input/mouse0)
[   139.684] (II) No input driver specified, ignoring this device.
[   139.684] (II) This device may have been added with another device file.
[   139.684] (II) config/udev: Adding input device A..... G3 (/dev/input/event4)
[   139.684] (**) A..... G3: Applying InputClass "evdev keyboard catchall"
[   139.684] (II) Using input driver 'evdev' for 'A..... G3'
[   139.684] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   139.684] (**) A..... G3: always reports core events
[   139.684] (**) evdev: A..... G3: Device: "/dev/input/event4"
[   139.684] (--) evdev: A..... G3: Vendor 0xe0ff Product 0x2
[   139.684] (--) evdev: A..... G3: Found 1 mouse buttons
[   139.684] (--) evdev: A..... G3: Found scroll wheel(s)
[   139.684] (--) evdev: A..... G3: Found relative axes
[   139.684] (II) evdev: A..... G3: Forcing relative x/y axes to exist.
[   139.684] (--) evdev: A..... G3: Found absolute axes
[   139.684] (II) evdev: A..... G3: Forcing absolute x/y axes to exist.
[   139.684] (--) evdev: A..... G3: Found keys
[   139.684] (II) evdev: A..... G3: Configuring as mouse
[   139.684] (II) evdev: A..... G3: Configuring as keyboard
[   139.684] (II) evdev: A..... G3: Adding scrollwheel support
[   139.684] (**) evdev: A..... G3: YAxisMapping: buttons 4 and 5
[   139.684] (**) evdev: A..... G3: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[   139.684] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.1/3-1.1:1.1/input/input4/event4"
[   139.684] (II) XINPUT: Adding extended input device "A..... G3" (type: KEYBOARD, id 10)
[   139.684] (**) Option "xkb_rules" "evdev"
[   139.684] (**) Option "xkb_model" "pc105"
[   139.684] (**) Option "xkb_layout" "pl"
[   139.685] (II) evdev: A..... G3: initialized for relative axes.
[   139.685] (WW) evdev: A..... G3: ignoring absolute axes.
[   139.685] (**) A..... G3: (accel) keeping acceleration scheme 1
[   139.685] (**) A..... G3: (accel) acceleration profile 0
[   139.685] (**) A..... G3: (accel) acceleration factor: 2.000
[   139.685] (**) A..... G3: (accel) acceleration threshold: 4
[   139.685] (II) config/udev: Adding input device Logitech USB Keyboard (/dev/input/event5)
[   139.685] (**) Logitech USB Keyboard: Applying InputClass "evdev keyboard catchall"
[   139.685] (II) Using input driver 'evdev' for 'Logitech USB Keyboard'
[   139.685] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   139.685] (**) Logitech USB Keyboard: always reports core events
[   139.685] (**) evdev: Logitech USB Keyboard: Device: "/dev/input/event5"
[   139.685] (--) evdev: Logitech USB Keyboard: Vendor 0x46d Product 0xc31d
[   139.685] (--) evdev: Logitech USB Keyboard: Found keys
[   139.685] (II) evdev: Logitech USB Keyboard: Configuring as keyboard
[   139.685] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.2/3-1.2:1.0/input/input5/event5"
[   139.685] (II) XINPUT: Adding extended input device "Logitech USB Keyboard" (type: KEYBOARD, id 11)
[   139.685] (**) Option "xkb_rules" "evdev"
[   139.685] (**) Option "xkb_model" "pc105"
[   139.685] (**) Option "xkb_layout" "pl"
[   139.686] (II) config/udev: Adding input device Logitech USB Keyboard (/dev/input/event6)
[   139.686] (**) Logitech USB Keyboard: Applying InputClass "evdev keyboard catchall"
[   139.686] (II) Using input driver 'evdev' for 'Logitech USB Keyboard'
[   139.686] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   139.686] (**) Logitech USB Keyboard: always reports core events
[   139.686] (**) evdev: Logitech USB Keyboard: Device: "/dev/input/event6"
[   139.686] (--) evdev: Logitech USB Keyboard: Vendor 0x46d Product 0xc31d
[   139.686] (--) evdev: Logitech USB Keyboard: Found absolute axes
[   139.686] (II) evdev: Logitech USB Keyboard: Forcing absolute x/y axes to exist.
[   139.686] (--) evdev: Logitech USB Keyboard: Found keys
[   139.686] (II) evdev: Logitech USB Keyboard: Configuring as mouse
[   139.686] (II) evdev: Logitech USB Keyboard: Configuring as keyboard
[   139.686] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.2/3-1.2:1.1/input/input6/event6"
[   139.686] (II) XINPUT: Adding extended input device "Logitech USB Keyboard" (type: KEYBOARD, id 12)
[   139.686] (**) Option "xkb_rules" "evdev"
[   139.686] (**) Option "xkb_model" "pc105"
[   139.686] (**) Option "xkb_layout" "pl"
[   139.686] (II) evdev: Logitech USB Keyboard: initialized for absolute axes.
[   139.686] (**) Logitech USB Keyboard: (accel) keeping acceleration scheme 1
[   139.686] (**) Logitech USB Keyboard: (accel) acceleration profile 0
[   139.686] (**) Logitech USB Keyboard: (accel) acceleration factor: 2.000
[   139.686] (**) Logitech USB Keyboard: (accel) acceleration threshold: 4
[   139.686] (II) config/udev: Adding input device PC Speaker (/dev/input/event2)
[   139.686] (II) No input driver specified, ignoring this device.
[   139.686] (II) This device may have been added with another device file.
[   413.440] (II) config/udev: removing device Logitech USB Keyboard
[   413.440] (II) evdev: Logitech USB Keyboard: Close
[   413.440] (II) UnloadModule: "evdev"
[   413.440] (II) Unloading evdev
[   413.476] (II) config/udev: removing device Logitech USB Keyboard
[   413.476] (II) evdev: Logitech USB Keyboard: Close
[   413.476] (II) UnloadModule: "evdev"
[   413.476] (II) Unloading evdev
[   416.291] (II) config/udev: Adding input device Logitech USB Keyboard (/dev/input/event5)
[   416.291] (**) Logitech USB Keyboard: Applying InputClass "evdev keyboard catchall"
[   416.291] (II) Using input driver 'evdev' for 'Logitech USB Keyboard'
[   416.291] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   416.291] (**) Logitech USB Keyboard: always reports core events
[   416.291] (**) evdev: Logitech USB Keyboard: Device: "/dev/input/event5"
[   416.291] (--) evdev: Logitech USB Keyboard: Vendor 0x46d Product 0xc31d
[   416.291] (--) evdev: Logitech USB Keyboard: Found keys
[   416.291] (II) evdev: Logitech USB Keyboard: Configuring as keyboard
[   416.291] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1c.1/0000:02:00.0/usb1/1-1/1-1:1.0/input/input8/event5"
[   416.291] (II) XINPUT: Adding extended input device "Logitech USB Keyboard" (type: KEYBOARD, id 11)
[   416.291] (**) Option "xkb_rules" "evdev"
[   416.291] (**) Option "xkb_model" "pc105"
[   416.291] (**) Option "xkb_layout" "pl"
[   416.291] (II) config/udev: Adding input device Logitech USB Keyboard (/dev/input/event6)
[   416.291] (**) Logitech USB Keyboard: Applying InputClass "evdev keyboard catchall"
[   416.291] (II) Using input driver 'evdev' for 'Logitech USB Keyboard'
[   416.291] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[   416.291] (**) Logitech USB Keyboard: always reports core events
[   416.291] (**) evdev: Logitech USB Keyboard: Device: "/dev/input/event6"
[   416.291] (--) evdev: Logitech USB Keyboard: Vendor 0x46d Product 0xc31d
[   416.291] (--) evdev: Logitech USB Keyboard: Found absolute axes
[   416.291] (II) evdev: Logitech USB Keyboard: Forcing absolute x/y axes to exist.
[   416.291] (--) evdev: Logitech USB Keyboard: Found keys
[   416.291] (II) evdev: Logitech USB Keyboard: Configuring as mouse
[   416.291] (II) evdev: Logitech USB Keyboard: Configuring as keyboard
[   416.291] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1c.1/0000:02:00.0/usb1/1-1/1-1:1.1/input/input9/event6"
[   416.291] (II) XINPUT: Adding extended input device "Logitech USB Keyboard" (type: KEYBOARD, id 12)
[   416.291] (**) Option "xkb_rules" "evdev"
[   416.292] (**) Option "xkb_model" "pc105"
[   416.292] (**) Option "xkb_layout" "pl"
[   416.292] (II) evdev: Logitech USB Keyboard: initialized for absolute axes.
[   416.292] (**) Logitech USB Keyboard: (accel) keeping acceleration scheme 1
[   416.292] (**) Logitech USB Keyboard: (accel) acceleration profile 0
[   416.292] (**) Logitech USB Keyboard: (accel) acceleration factor: 2.000
[   416.292] (**) Logitech USB Keyboard: (accel) acceleration threshold: 4

Bez xorg.conf ładnie chodzi i nawet jest akceleracja ale rozdziałka 1024x768 przy monitorze 1440x900 to trochę kicha :(

Kod:

intel@linux:~$ glxinfo | grep direct
direct rendering: Yes
intel@linux:~$

Ostatnio edytowany przez yomal79 (2012-04-23 21:53:06)

Yampress · 2012-04-23 21:55:39

A ile pamięci przydzieliłeś na tą grafike w BIOSie?

yomal79 · 2012-04-23 21:59:59

Max Jakieś 256mb

Jeszcze takie coś przy starcie mam Może kogoś naprowadzi

Kod:

intel@linux:~$ dmesg | grep intel
[    0.827416] intel_idle: MWAIT substates: 0x1120
[    0.827417] intel_idle: v0.4 model 0x2A
[    0.827418] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.241257] agpgart-intel 0000:00:00.0: Intel Sandybridge Chipset
[    1.241318] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[    1.241955] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
[    1.242047] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[    6.076487] fbcon: inteldrmfb (fb0) is primary device
[    6.455785] [drm:intel_dp_complete_link_train] *ERROR* failed to train DP, aborting
[    6.488668] fb0: inteldrmfb frame buffer device

i to

Kod:

intel@linux:~$ lspci -k | grep -A3 VGA
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
    Subsystem: Intel Corporation Device 2013
    Kernel driver in use: i915
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)

No masakra nawet compiz płynnie chodzi i wszystkie efekty :) a rozdzielczość nie do zmienienia...
Co się podziało z debianem ?

Ostatnio edytowany przez yomal79 (2012-04-23 22:27:09)

mati75 · 2012-04-23 23:37:54

Dziwne to trochę. U mnie na intelu od razu startuje w poprawnej rozdzielczości, poza tym nie używam xorg.conf. Pokaż:

Kod:

apt-cache policy libdrm2

oraz

Kod:

uname -r

Ostatnio edytowany przez mati75 (2012-04-23 23:38:28)

yomal79 · 2012-04-24 07:17:38

Kod:

intel@linux:~$ apt-cache policy libdrm2
libdrm2:
  Zainstalowana: 2.4.33-1
  Kandydująca:   2.4.33-1
  Tabela wersji:
 *** 2.4.33-1 0
        500 http://ftp.pl.debian.org/debian/ testing/main i386 Packages
        500 ftp://ftp.pl.debian.org/debian/ sid/main i386 Packages
        100 /var/lib/dpkg/status

Kod:

intel@linux:~$ uname -r
3.2.0-2-686-pae

Płyta DH61AG Na płycie są tylko wyjścia graficzne HDMI I DVI-D Grafika jest zintegrowana w procesorze S1155 Intel G620 HD2000

Ostatnio edytowany przez yomal79 (2012-04-24 07:19:10)

mer · 2012-04-25 14:07:09

xrandr, jak nie będzie twojej rozdziałki, dodaj do xorg'a modeline.

yomal79 · 2012-04-26 10:35:16

Problem po części rozwiązany Dzięki wszystkim za pomoc :)
Pomogło dodanie modeline do xorg.conf Wcześniej coś źle robiłem... Martwi mnie jednak że podczas generowania xorg mam

Kod:

(++) Using config file: "/root/xorg.conf.new"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
Number of created screens does not match number of detected devices.
Configuration failed.
Server terminated witch error (2). Closing log file.

Obecnie mam xfce4 i w ustawieniach monitora jest jeszcze DP3 pod moim monitorem Musiałem go odznaczyć bo miałem dwa pulpity jeden mniejszy a drugi większy Nie potrafie jednak zmienić w lightdm tego nakładania się obrazu Zna ktoś na to sposób ?

Ostatnio edytowany przez yomal79 (2012-04-26 10:40:35)

Time (s)	Query
0.00009	SET CHARSET latin2
0.00003	SET NAMES latin2
0.00086	SELECT u., g., o.logged FROM punbb_users AS u INNER JOIN punbb_groups AS g ON u.group_id=g.g_id LEFT JOIN punbb_online AS o ON o.ident='18.225.72.161' WHERE u.id=1
0.00066	REPLACE INTO punbb_online (user_id, ident, logged) VALUES(1, '18.225.72.161', 1732252972)
0.00042	SELECT * FROM punbb_online WHERE logged<1732252672
0.00072	SELECT topic_id FROM punbb_posts WHERE id=200781
0.00005	SELECT id FROM punbb_posts WHERE topic_id=21147 ORDER BY posted
0.00067	SELECT t.subject, t.closed, t.num_replies, t.sticky, f.id AS forum_id, f.forum_name, f.moderators, fp.post_replies, 0 FROM punbb_topics AS t INNER JOIN punbb_forums AS f ON f.id=t.forum_id LEFT JOIN punbb_forum_perms AS fp ON (fp.forum_id=f.id AND fp.group_id=3) WHERE (fp.read_forum IS NULL OR fp.read_forum=1) AND t.id=21147 AND t.moved_to IS NULL
0.00017	SELECT search_for, replace_with FROM punbb_censoring
0.00260	SELECT u.email, u.title, u.url, u.location, u.use_avatar, u.signature, u.email_setting, u.num_posts, u.registered, u.admin_note, p.id, p.poster AS username, p.poster_id, p.poster_ip, p.poster_email, p.message, p.hide_smilies, p.posted, p.edited, p.edited_by, g.g_id, g.g_user_title, o.user_id AS is_online FROM punbb_posts AS p INNER JOIN punbb_users AS u ON u.id=p.poster_id INNER JOIN punbb_groups AS g ON g.g_id=u.group_id LEFT JOIN punbb_online AS o ON (o.user_id=u.id AND o.user_id!=1 AND o.idle=0) WHERE p.topic_id=21147 ORDER BY p.id LIMIT 0,25
0.00096	UPDATE punbb_topics SET num_views=num_views+1 WHERE id=21147
Total query time: 0.00723 s

Forum Debian Users Gang

Ogłoszenie

#1 2012-04-23 08:00:54

yomal79 - Użytkownik

Zintegrowana grafika intel i niska rozdzielczość

Kod:

Kod:

#2 2012-04-23 11:54:56

mati75 - Psuj

Re: Zintegrowana grafika intel i niska rozdzielczość

Kod:

#3 2012-04-23 12:24:31

yomal79 - Użytkownik

Re: Zintegrowana grafika intel i niska rozdzielczość

Kod:

#4 2012-04-23 21:16:48

yomal79 - Użytkownik

Re: Zintegrowana grafika intel i niska rozdzielczość

Kod:

#5 2012-04-23 21:38:43

ArnVaker - Kapelusznik

Re: Zintegrowana grafika intel i niska rozdzielczość

#6 2012-04-23 21:41:53

yomal79 - Użytkownik

Re: Zintegrowana grafika intel i niska rozdzielczość

Kod:

Kod:

#7 2012-04-23 21:55:39

Yampress - Imperator

Re: Zintegrowana grafika intel i niska rozdzielczość

#8 2012-04-23 21:59:59

yomal79 - Użytkownik

Re: Zintegrowana grafika intel i niska rozdzielczość

Kod:

Kod:

#9 2012-04-23 23:37:54

mati75 - Psuj

Re: Zintegrowana grafika intel i niska rozdzielczość

Kod:

Kod:

#10 2012-04-24 07:17:38

yomal79 - Użytkownik

Re: Zintegrowana grafika intel i niska rozdzielczość

Kod:

Kod:

#11 2012-04-25 14:07:09

mer - Członek DUG

Re: Zintegrowana grafika intel i niska rozdzielczość

#12 2012-04-26 10:35:16

yomal79 - Użytkownik

Re: Zintegrowana grafika intel i niska rozdzielczość

Kod:

Stopka forum

Informacje debugowania