Nie jesteś zalogowany.
Jeśli nie posiadasz konta, zarejestruj je już teraz! Pozwoli Ci ono w pełni korzystać z naszego serwisu. Spamerom dziękujemy!

Ogłoszenie

Prosimy o pomoc dla małej Julki — przekaż 1% podatku na Fundacji Dzieciom zdazyć z Pomocą.
Więcej informacji na dug.net.pl/pomagamy/.

Strony: 1

 

#1  2013-11-09 10:14:52

  macios4x - Użytkownik

macios4x
Użytkownik
Zarejestrowany: 2012-12-10

gsmartcontrol - uszkodzony dysk??

Właśnie zainstalowałem gsmartcontrol i sprawdziłem twardziela czy coś z nim nie tak bo jednak już pare lat chodzi ten dysk troche leciwy. Zakładka "Error Log" na czerwono. Wynik:

Kod:

ATA Error Count: 78 (Note: Usually only the last five errors are stored.)

Kod:

Complete error log:

SMART Error Log Version: 1
ATA Error Count: 78 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 78 occurred at disk power-on lifetime: 4910 hours (204 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 37 38 04 e0  Error: UNC at LBA = 0x00043837 = 276535

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 78 37 04 e0 00      00:04:57.208  READ DMA EXT
  27 00 00 00 00 00 e0 00      00:05:03.950  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:05:03.888  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:05:03.887  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:05:03.875  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 77 occurred at disk power-on lifetime: 4910 hours (204 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 37 38 04 e0  Error: UNC at LBA = 0x00043837 = 276535

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 78 37 04 e0 00      00:04:57.208  READ DMA EXT
  27 00 00 00 00 00 e0 00      00:04:57.192  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:04:57.133  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:04:57.126  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:04:53.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 76 occurred at disk power-on lifetime: 4910 hours (204 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 37 38 04 e0  Error: UNC at LBA = 0x00043837 = 276535

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 78 37 04 e0 00      00:04:57.208  READ DMA EXT
  27 00 00 00 00 00 e0 00      00:04:57.192  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:04:57.133  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:04:57.126  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:04:53.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 75 occurred at disk power-on lifetime: 4910 hours (204 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 37 38 04 e0  Error: UNC at LBA = 0x00043837 = 276535

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 78 37 04 e0 00      00:04:50.426  READ DMA EXT
  27 00 00 00 00 00 e0 00      00:04:47.233  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:04:47.232  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:04:47.227  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:04:53.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 74 occurred at disk power-on lifetime: 4910 hours (204 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 37 38 04 e0  Error: UNC at LBA = 0x00043837 = 276535

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 78 37 04 e0 00      00:04:50.426  READ DMA EXT
  27 00 00 00 00 00 e0 00      00:04:47.233  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:04:47.232  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:04:47.227  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:04:47.225  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Niestety moja znajomośc angielskiego nie jest zbyt zadowalająca by się z tym uporać. Przydałoby się jakieś spolszczenie tego programu o ile jest.  Czy te błędy to coś poważnego?

Zwolennik Open Source, użytkownik Arch, Debian

Offline

 

#2  2013-11-09 12:26:22

  lx - Użytkownik

lx
Użytkownik
Zarejestrowany: 2010-06-22

Re: gsmartcontrol - uszkodzony dysk??

Kliknij View output i wklej zawartość, a w karcie Perform Tests wybierz Short Self-test i wykonaj go - to powinno zająć kilka minut. Sprawdź czy test nie wyrzucił jakichś błędów.

(aka mickul)

[url=http://sourceforge.net/projects/manpages-pl/]Polskie strony podręcznika systemowego[/url]

Offline

 

#3  2013-11-09 13:41:36

  macios4x - Użytkownik

macios4x
Użytkownik
Zarejestrowany: 2012-12-10

Re: gsmartcontrol - uszkodzony dysk??

Wynik:

Kod:

smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.11.6-1-ARCH] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.10
Device Model:     ST3160815AS
Serial Number:    9RA6VL9H
Firmware Version: 4.AAB
User Capacity:    160,041,885,696 bytes [160 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7 (minor revision not indicated)
Local Time is:    Sat Nov  9 13:37:00 2013 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)    Offline data collection activity
                    was completed without error.
                    Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever 
                    been run.
Total time to complete Offline 
data collection:         (  430) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine 
recommended polling time:      (   1) minutes.
Extended self-test routine
recommended polling time:      (  54) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   253   006    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0003   097   097   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   096   096   020    Old_age   Always       -       4661
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   085   060   030    Pre-fail  Always       -       353855244
  9 Power_On_Hours          0x0032   090   090   000    Old_age   Always       -       9568
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   096   096   020    Old_age   Always       -       4654
187 Reported_Uncorrect      0x0032   027   027   000    Old_age   Always       -       73
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   071   039   045    Old_age   Always   In_the_past 29 (0 114 29 23 0)
194 Temperature_Celsius     0x0022   029   061   000    Old_age   Always       -       29 (0 13 0 0 0)
195 Hardware_ECC_Recovered  0x001a   079   060   000    Old_age   Always       -       219684280
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 Data_Address_Mark_Errs  0x0032   100   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 78 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 78 occurred at disk power-on lifetime: 4910 hours (204 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 37 38 04 e0  Error: UNC at LBA = 0x00043837 = 276535

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 78 37 04 e0 00      00:04:57.208  READ DMA EXT
  27 00 00 00 00 00 e0 00      00:05:03.950  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:05:03.888  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:05:03.887  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:05:03.875  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 77 occurred at disk power-on lifetime: 4910 hours (204 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 37 38 04 e0  Error: UNC at LBA = 0x00043837 = 276535

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 78 37 04 e0 00      00:04:57.208  READ DMA EXT
  27 00 00 00 00 00 e0 00      00:04:57.192  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:04:57.133  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:04:57.126  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:04:53.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 76 occurred at disk power-on lifetime: 4910 hours (204 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 37 38 04 e0  Error: UNC at LBA = 0x00043837 = 276535

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 78 37 04 e0 00      00:04:57.208  READ DMA EXT
  27 00 00 00 00 00 e0 00      00:04:57.192  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:04:57.133  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:04:57.126  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:04:53.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 75 occurred at disk power-on lifetime: 4910 hours (204 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 37 38 04 e0  Error: UNC at LBA = 0x00043837 = 276535

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 78 37 04 e0 00      00:04:50.426  READ DMA EXT
  27 00 00 00 00 00 e0 00      00:04:47.233  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:04:47.232  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:04:47.227  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:04:53.955  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 74 occurred at disk power-on lifetime: 4910 hours (204 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 37 38 04 e0  Error: UNC at LBA = 0x00043837 = 276535

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 78 37 04 e0 00      00:04:50.426  READ DMA EXT
  27 00 00 00 00 00 e0 00      00:04:47.233  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      00:04:47.232  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      00:04:47.227  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 00      00:04:47.225  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      9565         -
# 2  Extended offline    Aborted by host               90%      8650         -
# 3  Short offline       Aborted by host               50%      8650         -
# 4  Short offline       Completed without error       00%         0         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Test zakończony pozytywnie, żadnych błędów.

Zwolennik Open Source, użytkownik Arch, Debian

Offline

 

#4  2013-11-09 14:20:26

  morfik - Cenzor wirtualnego świata

morfik
Cenzor wirtualnego świata
Skąd: ze WSI
Zarejestrowany: 2011-09-15
Serwis

Re: gsmartcontrol - uszkodzony dysk??

Kod:

7 Seek_Error_Rate         0x000f   085   060   030    Pre-fail  Always       -       353855244

07 Seek Error Rate - Częstość błędów wyszukiwania głowic magnetycznych. W razie uszkodzenia mechanicznego systemu pozycjonowania, uszkodzenia serwa albo termicznej rozszerzalności dysku, ilość błędów wyszukiwania wzrasta.
Więcej błędów wyszukiwania oznacza pogarszanie się stanu powierzchni dysku i podsystemu mechanicznego dysku. Nie jest to błąd krytyczny, ale warto go monitorować.[/quote]
Tyle ze na seagate dyskach to się inaczej liczy, z tego co piszą tutaj: http://forums.seagate.com/t5/Desktop-HDD-Desktop-SSHD/Seagate-s-Seek-Error-Rate-Raw-Read-Error-Rate-and-Hardware-ECC/td-p/122382 to po analizie pozostałych parametrów, wszystko jest w porządku, ale ja bym na twoim miejscu monitorował ten parametr, jeśli się będzie rósł, znaczy, że dysk się sypie powoli.

Kod:

 9 Power_On_Hours     9568

Nie taki znowu stary, u mnie jeden dysk (ale akurat nie podłączony) ma chyba 70k. xD

Ja tylko radzę, że jak chce się mieć rzetelny obraz sytuacji, to powinno się przeskanować dysk odpytując każdy jego sektor, co prawda to zajmie parę godzin na dużych dyskach ale wtedy raport smart będzie dokładny

Tutaj masz opis wszystkich  parametrów: http://www.elektroda.pl/rtvforum/topic1467175.html

Ostatnio edytowany przez morfik (2013-11-09 14:29:46)

Offline

 

 

Strony: 1

Stopka forum

Powered by PunBB
© Copyright 2002–2005 Rickard Andersson
Możesz wyłączyć AdBlock — tu nie ma reklam ;-)

[ Generated in 0.024 seconds, 13 queries executed ]

Informacje debugowania

Time (s) Query
0.00012 SET CHARSET latin2
0.00006 SET NAMES latin2
0.00122 SELECT u.*, g.*, o.logged FROM punbb_users AS u INNER JOIN punbb_groups AS g ON u.group_id=g.g_id LEFT JOIN punbb_online AS o ON o.ident='18.219.207.115' WHERE u.id=1
0.00117 REPLACE INTO punbb_online (user_id, ident, logged) VALUES(1, '18.219.207.115', 1732223462)
0.00092 SELECT * FROM punbb_online WHERE logged<1732223162
0.00116 DELETE FROM punbb_online WHERE ident='18.191.202.48'
0.00087 DELETE FROM punbb_online WHERE ident='3.129.247.250'
0.00154 SELECT topic_id FROM punbb_posts WHERE id=245416
0.00608 SELECT id FROM punbb_posts WHERE topic_id=24573 ORDER BY posted
0.00087 SELECT t.subject, t.closed, t.num_replies, t.sticky, f.id AS forum_id, f.forum_name, f.moderators, fp.post_replies, 0 FROM punbb_topics AS t INNER JOIN punbb_forums AS f ON f.id=t.forum_id LEFT JOIN punbb_forum_perms AS fp ON (fp.forum_id=f.id AND fp.group_id=3) WHERE (fp.read_forum IS NULL OR fp.read_forum=1) AND t.id=24573 AND t.moved_to IS NULL
0.00016 SELECT search_for, replace_with FROM punbb_censoring
0.00570 SELECT u.email, u.title, u.url, u.location, u.use_avatar, u.signature, u.email_setting, u.num_posts, u.registered, u.admin_note, p.id, p.poster AS username, p.poster_id, p.poster_ip, p.poster_email, p.message, p.hide_smilies, p.posted, p.edited, p.edited_by, g.g_id, g.g_user_title, o.user_id AS is_online FROM punbb_posts AS p INNER JOIN punbb_users AS u ON u.id=p.poster_id INNER JOIN punbb_groups AS g ON g.g_id=u.group_id LEFT JOIN punbb_online AS o ON (o.user_id=u.id AND o.user_id!=1 AND o.idle=0) WHERE p.topic_id=24573 ORDER BY p.id LIMIT 0,25
0.00101 UPDATE punbb_topics SET num_views=num_views+1 WHERE id=24573
Total query time: 0.02088 s