Forum Debian Users Gang

harlequin · 2006-04-24 22:22:15

Tak czytam sobie po raz kolejny opisy adsl/neo/usb na linuksach, i chciałem spróbować jeszcze raz, chociaż nigdy wcześniej nie wyszło ( ubuntu, fedora,debian mandrake, mandriva) :(.
Teraz próbuję na slackwarze 10.2 ker. 2.4.31.
Pobrałem wór eagle-usb-x.x.x i dawaj. Jedynie eagle-usb.2.1.1 wywarło jakąs reakcję na sagemie inną niż "error" przy próbie komunikacji po eagleconfig czy "modem nie działa!" po startadsl.
Przy wersji 2.1.1 nie ma w/w błędów, synchronizacja sie powiodła, ale startadsl wypisuje po czasie "nie udało się ustanowić połączenia".

takie cudo mam min:

Kod:

Diagnostic (1.21 2005/01/16) driver eagle-usb 20060424142426 
# System Information 
Linux darkstar 2.4.31 #6 Sun Jun 5 19:04:47 PDT 2005 i686 unknown unknown GNU/Linux 
Slackware 10.2.0 
Linux version 2.4.31 (root@tree) (gcc version 3.3.5) #6 Sun Jun 5 19:04:47 PDT 2005 
gcc version 3.3.6 used : 3.3.6 
# module loaded ?        [ OK ] 
# modem operational ?    [ OK ] 
# Config vpi/vci/encapsulation/isp :  23 6 (pppoa) PL01 
# pppd launched ?        [ KO ] 
# ping IP ?              [ KO ] 
# test DNS resolution ?  [ KO ] 
##Complete diagnostic has been saved on /var/log/eagle-usb/eagle_diag_20060424142426.txt 
##Please keep only relevant data and remove personal informations.

przy próbie łączenia się (kończącej się niepowodzeniem) tak wygląda ppp0:

Kod:

root@darkstar:~# ifconfig ppp0 
ppp0      Link encap:Point-to-Point Protocol 
          POINTOPOINT NOARP MULTICAST  MTU:1500  Metric:1 
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 
          collisions:0 txqueuelen:3 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

Kod:

Driver version 2.1.1     Chipset: Eagle0 
Vendor ID : 0x1110     Product ID : 0x9031   Rev: 0x200b 
USB Bus : 002    USB Device : 002    Dbg mask: 0x0 
Ethernet Interface : none 
MAC: xx:xx:xx:xx:xx:xx 
Tx Rate           0  Rx Rate           0 
FEC               0  Margin            0  Atten             0 dB 
VID-CPE           0  VID-CO            0  HEC               0 


VPI               0  VCI              35  Delin          GOOD 


Cells Tx          0  Cells Rx          0 
Pkts Tx           0  Pkts Rx           0 
OAM               0  Bad VPI           0  Bad CRC           0 
Oversiz.          0 

Modem is booting

Piszą mądrzy ludzie w knigach grubych, że linuksy z modemami usb na adsl to tak sobie ... ale czytałem wiele opisów osób, którym się udało.
I nie wiem czy ja mam modem jakiś inny niż wszyscy (szary sagem fast 800) czy dom na cmentarzysku indian , że u mnie nie idzie tego zdielać?

* oczywiście opisałem "tragiczną sytuację" na forum od slacka, ale pomyślałem sobie, ze nie zabijecie jak wrzuce taki post do "luźnych rozmów"... a może ktoś miał taki problem a go rozwiązał i zechce się podzielić doświadczeniem.

kamikaze · 2006-04-25 08:55:22

Zajrzyj do logów, cos powinno być.

harlequin · 2006-04-25 10:36:38

Kod:

Apr 25 00:59:32 darkstar insmod: insmod: a module named eagle-usb already exists
Apr 25 00:59:32 darkstar insmod: insmod: insmod eagle-usb failed
Apr 25 00:59:32 darkstar insmod: insmod: a module named eagle-usb already exists
Apr 25 00:59:32 darkstar insmod: insmod: insmod eagle-usb failed
Apr 25 01:00:17 darkstar kernel: NVRM: RmInitAdapter failed! (0x25:0xffffffff:1025)
Apr 25 01:00:17 darkstar kernel: NVRM: rm_init_adapter(0) failed
Apr 25 01:00:55 darkstar kernel: spurious 8259A interrupt: IRQ7.
Apr 25 01:06:17 darkstar pppd[2447]: LCP: timeout sending Config-Requests 
Apr 25 01:06:17 darkstar pppoa[2450]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:06:48 darkstar pppd[2447]: LCP: timeout sending Config-Requests 
Apr 25 01:06:48 darkstar pppoa[2522]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:07:19 darkstar pppd[2447]: LCP: timeout sending Config-Requests 
Apr 25 01:07:19 darkstar pppoa[2600]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:07:50 darkstar pppd[2447]: LCP: timeout sending Config-Requests 
Apr 25 01:07:50 darkstar pppoa[2678]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:08:21 darkstar pppd[2447]: LCP: timeout sending Config-Requests 
Apr 25 01:08:21 darkstar pppoa[2755]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:08:52 darkstar pppd[2447]: LCP: timeout sending Config-Requests 
Apr 25 01:08:52 darkstar pppoa[2831]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:09:23 darkstar pppd[2447]: LCP: timeout sending Config-Requests 
Apr 25 01:09:23 darkstar pppoa[2908]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:09:55 darkstar pppd[2447]: LCP: timeout sending Config-Requests 
Apr 25 01:09:55 darkstar pppoa[2984]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:10:26 darkstar pppd[2447]: LCP: timeout sending Config-Requests 
Apr 25 01:10:26 darkstar pppoa[3062]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:10:57 darkstar pppd[2447]: LCP: timeout sending Config-Requests 
Apr 25 01:10:57 darkstar pppoa[3139]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:13:42 darkstar pppd[3354]: LCP: timeout sending Config-Requests 
Apr 25 01:13:42 darkstar pppoa[3356]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:14:13 darkstar pppd[3354]: LCP: timeout sending Config-Requests 
Apr 25 01:14:13 darkstar pppoa[3429]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:14:46 darkstar pppd[3354]: LCP: timeout sending Config-Requests 
Apr 25 01:14:46 darkstar pppoa[3586]: read (AsyncReadFromPPP): Input/output error
Apr 25 01:15:05 darkstar pppoa[3688]: recv (ReceivePacket): Network is down
Apr 25 01:15:08 darkstar pppoa[3688]: sendto (SendPPPPacket size: 20): Network is down

Kod:

Apr 25 00:59:31 darkstar kernel: usb-uhci.c: High bandwidth mode enabled
Apr 25 00:59:31 darkstar kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Apr 25 00:59:32 darkstar kernel: [eagle-usb] driver V2.1.1 loaded
Apr 25 00:59:32 darkstar kernel: usb.c: registered new driver eagle-usb
Apr 25 00:59:32 darkstar kernel: [eagle-usb] New USB ADSL device detected, waiting for DSP code...
Apr 25 00:59:32 darkstar kernel: [eagle-usb] created proc entry at : /proc/driver/eagle-usb/002-002
Apr 25 00:59:33 darkstar kernel: [eagle-usb] ioctl EU_IO_OPTIONS received
Apr 25 00:59:33 darkstar last message repeated 2 times
Apr 25 00:59:33 darkstar logger: Unknown option on line 27 
                                      ...................
Apr 25 00:59:33 darkstar logger: Unknown option on line 32
Apr 25 00:59:33 darkstar kernel: [eagle-usb] ioctl EU_IO_DSP received
Apr 25 00:59:33 darkstar kernel: [eagle-usb] Loading DSP code to device...
Apr 25 00:59:33 darkstar kernel: [eagle-usb] DSP code successfully loaded to device
Apr 25 00:59:33 darkstar kernel: [eagle-usb] ioctl EU_IO_DSP received
Apr 25 00:59:33 darkstar kernel: [eagle-usb] Loading DSP code to device...
Apr 25 00:59:33 darkstar kernel: [eagle-usb] DSP code successfully loaded to device
Apr 25 00:59:33 darkstar kernel: [eagle-usb] ioctl EU_IO_DSP received
Apr 25 00:59:33 darkstar kernel: [eagle-usb] Loading DSP code to device...
Apr 25 00:59:33 darkstar kernel: [eagle-usb] DSP code successfully loaded to device
Apr 25 00:59:33 darkstar logger: Options successfully sent to driver.
Apr 25 00:59:33 darkstar logger: Using DSP code for POTS line
Apr 25 00:59:33 darkstar logger: DSP code successfully loaded.
Apr 25 00:59:33 darkstar logger: Options successfully sent to driver.
Apr 25 00:59:33 darkstar logger: Using DSP code for POTS line
Apr 25 00:59:33 darkstar logger: DSP code successfully loaded.
Apr 25 00:59:33 darkstar logger: Options successfully sent to driver.
Apr 25 00:59:33 darkstar logger: Using DSP code for POTS line
Apr 25 00:59:33 darkstar logger: DSP code successfully loaded.
Apr 25 00:59:33 darkstar kernel: usb.c: registered new driver acm
Apr 25 00:59:33 darkstar kernel: acm.c: v0.21:USB Abstract Control Model driver for USB modems and ISDN adapters
Apr 25 00:59:45 darkstar logger: /etc/rc.d/rc.hotplug start (exiting script)
Apr 25 00:59:50 darkstar kernel: [eagle-usb] Modem operational !!
Apr 25 00:59:50 darkstar kernel: [eagle-usb]  Ethernet device eth1 created.
Apr 25 01:05:46 darkstar kernel: CSLIP: code copyright 1989 Regents of the University of California
Apr 25 01:05:46 darkstar kernel: PPP generic driver version 2.4.2
Apr 25 01:05:46 darkstar pppd[2447]: pppd 2.4.4b1 started by root, uid 0
Apr 25 01:05:46 darkstar pppd[2447]: Using interface ppp0
Apr 25 01:05:46 darkstar pppd[2447]: Connect: ppp0 <--> /dev/pts/6
Apr 25 01:06:17 darkstar pppd[2447]: Connection terminated.
Apr 25 01:06:17 darkstar pppd[2447]: Modem hangup
Apr 25 01:06:17 darkstar pppd[2447]: Using interface ppp0
Apr 25 01:06:17 darkstar pppd[2447]: Connect: ppp0 <--> /dev/pts/7
Apr 25 01:06:48 darkstar pppd[2447]: Connection terminated.
Apr 25 01:06:48 darkstar pppd[2447]: Modem hangup
Apr 25 01:06:48 darkstar pppd[2447]: Using interface ppp0
Apr 25 01:06:48 darkstar pppd[2447]: Connect: ppp0 <--> /dev/pts/6
Apr 25 01:07:19 darkstar pppd[2447]: Connection terminated.
Apr 25 01:07:19 darkstar pppd[2447]: Modem hangup
Apr 25 01:07:19 darkstar pppd[2447]: Using interface ppp0
Apr 25 01:07:19 darkstar pppd[2447]: Connect: ppp0 <--> /dev/pts/7
Apr 25 01:07:50 darkstar pppd[2447]: Connection terminated.
                      ........................................

eagle-usb.conf

Kod:

<eaglectrl>
# Options are set whith the following syntax:
#
# Name = Value
#
# where "Name" is the option name, and
# "Value" is the option value, specified
# in hexadecimal (without any prefix).
# Option names are case sensitive.
# Options that are commented out are specified
# with their default values.
#
# Other than VPI, VCI and Encapsulation,
# I really don't known what these options mean.

#POTS FOR EAGLE
# those values come from file CMVep.txt
OPTN0=80008066
OPTN1=00000994
OPTN2=63600000
OPTN3=00000028
OPTN4=00600000
OPTN5=00000500
# OPTN6=00000000
# OPTN7=02CD8044 
# OPTN15=09090909
OPTN18=820200FF
OPTN19=80000000
OPTN20=11900002 
OPTN70=218280AA
OPTN72=006F06EB
OPTN73=00010060
# not implemented, don't know how to :-(
#cw mask 8 0x3fffffc0
#cw diag 0 0x26870030
#cw flag 0 0x00000820
#;These OPTN 0,18,19 are for non-TR-48
#cw optn 0 0x80020066
#cw optn 18 0x00000000
#cw optn 19 0x00000000
#;These OPTN 0,18,19 are for TR-48
#;cw optn 0 0x80008066
#;cw optn 18 0x820200ff
#;cw optn 19 0x80000000
#CW cntl 0 2
#Enable OPTN16 for WT-062 testing only
#OPTN16=80818040

# VPI / VCI are in hexa (8, 23) is 8,35 in decimal
VPI=00000000
VCI=00000035   ***BYŁO 0...023  ale ponoć dla neostrady ma być 35, prawda ? ***


#The following values are valid for encapsulation :
#MPOA_MODE_BRIDGED_ETH_LLC ----> 1
#MPOA_MODE_BRIDGED_ETH_VC  ----> 2
#MPOA_MODE_ROUTED_IP_LLC   ----> 3
#MPOA_MODE_ROUTED_IP_VC    ----> 4
#MPOA_MODE_PPPOA_LLC       ----> 5
#MPOA_MODE_PPPOA_VC        ----> 6
Encapsulation=00000006

Linetype=00000001
RatePollFreq=00000009
</eaglectrl>
STATIC_IP=none
ISP=PL01
LANG=p2
ASYNCHRONOUS_START=1

mars · 2006-04-29 16:29:09

Spróbuj według tych opisów. Nie ręczę głową bo sam mam modem SpeedTouch, ale opisy z tych żródeł dla mojego modemu są skuteczne.

Dla Debiana
[url]http://www.szarp.com.pl/howto/howto/html/neostrada-usb.html[/url]

Dla KateOS (powinno działać także na Slackware. KateOS używa kernela z serii 2.6, więc może trzeba będzie użyć jądra z tej serii na Slacku?)
[url]http://wikidoc.kateos.org/index.php/Instalacja_modemu_Sagem_F%40st_800[/url]

---------------------------------------
P.S. To mój pierwszy post tutaj więc serdecznie witam wszystkich.

Pozdrawiam
mars

harlequin · 2006-04-29 17:13:08

Dzięki mars za podrzucenie opisów. Ale sprawa na dzień dzisiejszy jest słoneczna ;) . Eagle wszelkiej maści spływały po sagemie jak woda po kaczce, nie wywierając na nim zbytniej uwagi.
Więc spróbowałem ostatniej deski ratunku:
1. Zrobiłem sobie kernel 2.6.16.9
2. Wrzuciłem ueagle-data-1.1
efekt:
alles ok :)

... trochę dużo "strzałów" trzeba wykonać z tą neo ale liczy sie sukces na końcu..

mars · 2006-04-30 20:14:42

Nie ma za co. Gratuluje! Ja sie męczyłem się kilka miesięcy ze SpeedTouch-em

Pozdrawiam

mars

Time (s)	Query
0.00010	SET CHARSET latin2
0.00004	SET NAMES latin2
0.00153	SELECT u., g., o.logged FROM punbb_users AS u INNER JOIN punbb_groups AS g ON u.group_id=g.g_id LEFT JOIN punbb_online AS o ON o.ident='3.149.247.78' WHERE u.id=1
0.00115	REPLACE INTO punbb_online (user_id, ident, logged) VALUES(1, '3.149.247.78', 1738334794)
0.00026	SELECT * FROM punbb_online WHERE logged<1738334494
0.00094	DELETE FROM punbb_online WHERE ident='18.117.184.236'
0.00070	DELETE FROM punbb_online WHERE ident='3.128.206.7'
0.00060	SELECT topic_id FROM punbb_posts WHERE id=26756
0.00004	SELECT id FROM punbb_posts WHERE topic_id=3401 ORDER BY posted
0.00072	SELECT t.subject, t.closed, t.num_replies, t.sticky, f.id AS forum_id, f.forum_name, f.moderators, fp.post_replies, 0 FROM punbb_topics AS t INNER JOIN punbb_forums AS f ON f.id=t.forum_id LEFT JOIN punbb_forum_perms AS fp ON (fp.forum_id=f.id AND fp.group_id=3) WHERE (fp.read_forum IS NULL OR fp.read_forum=1) AND t.id=3401 AND t.moved_to IS NULL
0.00005	SELECT search_for, replace_with FROM punbb_censoring
0.00203	SELECT u.email, u.title, u.url, u.location, u.use_avatar, u.signature, u.email_setting, u.num_posts, u.registered, u.admin_note, p.id, p.poster AS username, p.poster_id, p.poster_ip, p.poster_email, p.message, p.hide_smilies, p.posted, p.edited, p.edited_by, g.g_id, g.g_user_title, o.user_id AS is_online FROM punbb_posts AS p INNER JOIN punbb_users AS u ON u.id=p.poster_id INNER JOIN punbb_groups AS g ON g.g_id=u.group_id LEFT JOIN punbb_online AS o ON (o.user_id=u.id AND o.user_id!=1 AND o.idle=0) WHERE p.topic_id=3401 ORDER BY p.id LIMIT 0,25
0.00098	UPDATE punbb_topics SET num_views=num_views+1 WHERE id=3401
Total query time: 0.00914 s

Forum Debian Users Gang

Ogłoszenie

#1 2006-04-24 22:22:15

harlequin - Użytkownik

sagem/neostrada/usb

Kod:

Kod:

Kod:

#2 2006-04-25 08:55:22

kamikaze - Administrator

Re: sagem/neostrada/usb

#3 2006-04-25 10:36:38

harlequin - Użytkownik

Re: sagem/neostrada/usb

Kod:

Kod:

Kod:

#4 2006-04-29 16:29:09

mars - Nowy użytkownik

Re: sagem/neostrada/usb

#5 2006-04-29 17:13:08

harlequin - Użytkownik

Re: sagem/neostrada/usb

#6 2006-04-30 20:14:42

mars - Nowy użytkownik

Re: sagem/neostrada/usb

Stopka forum

Informacje debugowania