Forum Debian Users Gang

basert · 2017-08-20 22:38:51

Witam.

Mam problem z instalacją karty wifi.

dpkg --print-architecture

Kod:

 amd64

ifconfig

Kod:

eth0: flags=-28605<UP,BROADCAST,RUNNING,MULTICAST,DYNAMIC>  mtu 1500
        inet 192.168.1.105  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 fe80::faa9:63ff:fe3f:a038  prefixlen 64  scopeid 0x20<link>
        ether f8:a9:63:3f:a0:38  txqueuelen 1000  (Ethernet)
        RX packets 37150  bytes 33708107 (32.1 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 32163  bytes 3980083 (3.7 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 16  

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1  (Local Loopback)
        RX packets 4493  bytes 411830 (402.1 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 4493  bytes 411830 (402.1 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lspci -k

Kod:

00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09)
    Subsystem: Lenovo 3rd Gen Core processor DRAM Controller
    Kernel driver in use: ivb_uncore
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09)
    Kernel driver in use: pcieport
    Kernel modules: shpchp
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
    Subsystem: Lenovo 3rd Gen Core processor Graphics Controller
    Kernel driver in use: i915
    Kernel modules: i915
00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04)
    Subsystem: Lenovo 7 Series/C210 Series Chipset Family USB xHCI Host Controller
    Kernel driver in use: xhci_hcd
    Kernel modules: xhci_pci
00:16.0 Communication controller: Intel Corporation 7 Series/C216 Chipset Family MEI Controller #1 (rev 04)
    Subsystem: Lenovo 7 Series/C216 Chipset Family MEI Controller
    Kernel driver in use: mei_me
    Kernel modules: mei_me
00:1a.0 USB controller: Intel Corporation 7 Series/C216 Chipset Family USB Enhanced Host Controller #2 (rev 04)
    Subsystem: Lenovo 7 Series/C216 Chipset Family USB Enhanced Host Controller
    Kernel driver in use: ehci-pci
    Kernel modules: ehci_pci
00:1b.0 Audio device: Intel Corporation 7 Series/C216 Chipset Family High Definition Audio Controller (rev 04)
    Subsystem: Lenovo 7 Series/C216 Chipset Family High Definition Audio Controller
    Kernel driver in use: snd_hda_intel
    Kernel modules: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 7 Series/C216 Chipset Family PCI Express Root Port 1 (rev c4)
    Kernel driver in use: pcieport
    Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4)
    Kernel driver in use: pcieport
    Kernel modules: shpchp
00:1d.0 USB controller: Intel Corporation 7 Series/C216 Chipset Family USB Enhanced Host Controller #1 (rev 04)
    Subsystem: Lenovo 7 Series/C216 Chipset Family USB Enhanced Host Controller
    Kernel driver in use: ehci-pci
    Kernel modules: ehci_pci
00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04)
    Subsystem: Lenovo HM76 Express Chipset LPC Controller
    Kernel driver in use: lpc_ich
    Kernel modules: lpc_ich
00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
    Subsystem: Lenovo 7 Series Chipset Family 6-port SATA Controller [AHCI mode]
    Kernel driver in use: ahci
    Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 7 Series/C216 Chipset Family SMBus Controller (rev 04)
    Subsystem: Lenovo 7 Series/C216 Chipset Family SMBus Controller
    Kernel driver in use: i801_smbus
    Kernel modules: i2c_i801
01:00.0 Display controller: Advanced Micro Devices, Inc. [AMD/ATI] Mars [Radeon HD 8670A/8670M/8750M]
    Subsystem: Lenovo Mars [Radeon HD 8670A/8670M/8750M]
    Kernel modules: radeon
02:00.0 Ethernet controller: Qualcomm Atheros QCA8172 Fast Ethernet (rev 10)
    Subsystem: Lenovo QCA8172 Fast Ethernet
    Kernel driver in use: alx
    Kernel modules: alx
03:00.0 Network controller: Broadcom Limited BCM43142 802.11b/g/n (rev 01)
    Subsystem: Lenovo BCM43142 802.11b/g/n

iwconfig

Kod:

eth0      no wireless extensions.
lo        no wireless extensions.

ifup wlan0

Kod:

ifup: unknown interface wlan0

Tutaj jest błąd:

apt-get install linux-image-$(uname -r|sed 's,[^-]*-[^-]*-,,') linux-headers-$(uname -r|sed 's,[^-]*-[^-]*-,,') broadcom-sta-dkms

Kod:

Czytanie list pakietów... Gotowe
Budowanie drzewa zależności       
Odczyt informacji o stanie... Gotowe
linux-headers-amd64 is already the newest version (4.9+80+deb9u1).
linux-image-amd64 is already the newest version (4.9+80+deb9u1).
Następujący pakiet został zainstalowany automatycznie i nie jest już więcej wymagany:
  module-assistant
Aby go usunąć należy użyć "apt autoremove".
Zostaną zainstalowane następujące NOWE pakiety:
  broadcom-sta-dkms
0 aktualizowanych, 1 nowo instalowanych, 0 usuwanych i 0 nieaktualizowanych.
Konieczne pobranie 0 B/2170 kB archiwów.
Po tej operacji zostanie dodatkowo użyte 14,4 MB miejsca na dysku.
Kontynuować? [T/n] T
Wybieranie wcześniej niewybranego pakietu broadcom-sta-dkms.
(Odczytywanie bazy danych ... 171657 plików i katalogów obecnie zainstalowanych.)
Przygotowywanie do rozpakowania pakietu .../broadcom-sta-dkms_6.30.223.248-3_all.deb ...
Rozpakowywanie pakietu broadcom-sta-dkms (6.30.223.248-3) ...
Konfigurowanie pakietu broadcom-sta-dkms (6.30.223.248-3) ...
Loading new broadcom-sta-6.30.223.248 DKMS files...
Building for 4.9.0-3-amd64
Building initial module for 4.9.0-3-amd64
Error! Bad return status for module build on kernel: 4.9.0-3-amd64 (x86_64)
Consult /var/lib/dkms/broadcom-sta/6.30.223.248/build/make.log for more information..

modprobe wl

Kod:

modprobe: ERROR: ../libkmod/libkmod-module.c:832 kmod_module_insert_module() could not find module by name='wl'
modprobe: ERROR: could not insert 'wl': Unknown symbol in module, or unknown parameter (see dmesg)
modprobe: ERROR: ../libkmod/libkmod-module.c:977 command_do() Error running install command for wl
modprobe: ERROR: could not insert 'wl': Operation not permitted

Proszę o pomoc.

arecki · 2017-08-20 22:41:33

Kod:

Consult /var/lib/dkms/broadcom-sta/6.30.223.248/build/make.log for more information..

basert · 2017-08-20 22:48:27

Kod:

DKMS make.log for broadcom-sta-6.30.223.248 for kernel 4.9.0-3-amd64 (x86_64)
nie, 20 sie 2017, 22:33:05 CEST
/bin/sh: 1: [: Illegal number: 
/bin/sh: 1: [: Illegal number: 
Wireless Extension is the only possible API for this kernel version
Using Wireless Extension API
KBUILD_NOPEDANTIC=1 make -C /lib/modules/4.9.0-3-amd64/build M=`pwd`
make[1]: uwaga: serwer zadań niedostępny: użycie -j1. Należy dodać `+' do nadrzędnej reguły make.
make[1]: Wejście do katalogu '/usr/src/linux-headers-4.9.0-3-amd64'
CFG80211 API is prefered for this kernel version
Using CFG80211 API
Kernel architecture is X86_64
  LD      /var/lib/dkms/broadcom-sta/6.30.223.248/build/built-in.o
  CC [M]  /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/shared/linux_osl.o
  CC [M]  /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_linux.o
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_linux.c: In function ‘wl_pci_probe’:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_linux.c:772:2: warning: this ‘if’ clause does not guard... [-Wmisleading-indentation]
  if ((val & 0x0000ff00) != 0)
  ^~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_linux.c:774:3: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘if’
   bar1_size = pci_resource_len(pdev, 2);
   ^~~~~~~~~
  CC [M]  /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_iw.o
  CC [M]  /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.o
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:232:12: error: ‘IEEE80211_BAND_2GHZ’ undeclared here (not in a function)
  .band   = IEEE80211_BAND_2GHZ,  \
            ^
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:278:2: note: in expansion of macro ‘CHAN2G’
  CHAN2G(1, 2412, 0),
  ^~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:241:12: error: ‘IEEE80211_BAND_5GHZ’ undeclared here (not in a function)
  .band   = IEEE80211_BAND_5GHZ,  \
            ^
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:295:2: note: in expansion of macro ‘CHAN5G’
  CHAN5G(34, 0), CHAN5G(36, 0),
  ^~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:241:12: note: (near initialization for ‘__wl_5ghz_n_channels[109].band’)
  .band   = IEEE80211_BAND_5GHZ,  \
            ^
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:371:18: note: in expansion of macro ‘CHAN5G’
  CHAN5G(226, 0), CHAN5G(228, 0),
                  ^~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:375:10: error: initializer element is not constant
  .band = IEEE80211_BAND_2GHZ,
          ^~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:375:10: note: (near initialization for ‘__wl_band_2ghz.band’)
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:383:10: error: initializer element is not constant
  .band = IEEE80211_BAND_5GHZ,
          ^~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:383:10: note: (near initialization for ‘__wl_band_5ghz_a.band’)
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:391:10: error: initializer element is not constant
  .band = IEEE80211_BAND_5GHZ,
          ^~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:391:10: note: (near initialization for ‘__wl_band_5ghz_n.band’)
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_cfg80211_get_key’:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1390:9: warning: passing argument 1 of ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
  memcpy(params.key, key.data, params.key_len);
         ^~~~~~
In file included from /usr/src/linux-headers-4.9.0-3-common/arch/x86/include/asm/string.h:4:0,
                 from /usr/src/linux-headers-4.9.0-3-common/include/linux/string.h:18,
                 from /usr/src/linux-headers-4.9.0-3-common/include/linux/bitmap.h:8,
                 from /usr/src/linux-headers-4.9.0-3-common/include/linux/cpumask.h:11,
                 from /usr/src/linux-headers-4.9.0-3-common/arch/x86/include/asm/cpumask.h:4,
                 from /usr/src/linux-headers-4.9.0-3-common/arch/x86/include/asm/msr.h:10,
                 from /usr/src/linux-headers-4.9.0-3-common/arch/x86/include/asm/processor.h:20,
                 from /usr/src/linux-headers-4.9.0-3-common/arch/x86/include/asm/cpufeature.h:4,
                 from /usr/src/linux-headers-4.9.0-3-common/arch/x86/include/asm/thread_info.h:52,
                 from /usr/src/linux-headers-4.9.0-3-common/include/linux/thread_info.h:58,
                 from /usr/src/linux-headers-4.9.0-3-common/arch/x86/include/asm/preempt.h:6,
                 from /usr/src/linux-headers-4.9.0-3-common/include/linux/preempt.h:59,
                 from /usr/src/linux-headers-4.9.0-3-common/include/linux/spinlock.h:50,
                 from /usr/src/linux-headers-4.9.0-3-common/include/linux/seqlock.h:35,
                 from /usr/src/linux-headers-4.9.0-3-common/include/linux/time.h:5,
                 from /usr/src/linux-headers-4.9.0-3-common/include/linux/stat.h:18,
                 from /usr/src/linux-headers-4.9.0-3-common/include/linux/module.h:10,
                 from /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/include/linuxver.h:40,
                 from /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:26:
/usr/src/linux-headers-4.9.0-3-common/arch/x86/include/asm/string_64.h:31:14: note: expected ‘void *’ but argument is of type ‘const u8 * {aka const unsigned char *}’
 extern void *memcpy(void *to, const void *from, size_t len);
              ^~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_cfg80211_get_station’:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1444:20: error: ‘STATION_INFO_TX_BITRATE’ undeclared (first use in this function)
   sinfo->filled |= STATION_INFO_TX_BITRATE;
                    ^~~~~~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1444:20: note: each undeclared identifier is reported only once for each function it appears in
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1444:17: error: invalid operands to binary | (have ‘u64 {aka long long unsigned int}’ and ‘struct ieee80211_channel *’)
   sinfo->filled |= STATION_INFO_TX_BITRATE;
                 ^~ ~~~~~~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1444:3: warning: statement with no effect [-Wunused-value]
   sinfo->filled |= STATION_INFO_TX_BITRATE;
   ^~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1457:20: error: ‘STATION_INFO_SIGNAL’ undeclared (first use in this function)
   sinfo->filled |= STATION_INFO_SIGNAL;
                    ^~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1457:17: error: invalid operands to binary | (have ‘u64 {aka long long unsigned int}’ and ‘struct ieee80211_channel *’)
   sinfo->filled |= STATION_INFO_SIGNAL;
                 ^~ ~~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1457:3: warning: statement with no effect [-Wunused-value]
   sinfo->filled |= STATION_INFO_SIGNAL;
   ^~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c: At top level:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1778:17: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
  .get_station = wl_cfg80211_get_station,
                 ^~~~~~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1778:17: note: (near initialization for ‘wl_cfg80211_ops.get_station’)
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_alloc_wdev’:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1858:20: error: array subscript is not an integer
  wdev->wiphy->bands[IEEE80211_BAND_2GHZ] = &__wl_band_2ghz;
                    ^
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1858:2: warning: statement with no effect [-Wunused-value]
  wdev->wiphy->bands[IEEE80211_BAND_2GHZ] = &__wl_band_2ghz;
  ^~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1859:20: error: array subscript is not an integer
  wdev->wiphy->bands[IEEE80211_BAND_5GHZ] = &__wl_band_5ghz_a;
                    ^
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1859:2: warning: statement with no effect [-Wunused-value]
  wdev->wiphy->bands[IEEE80211_BAND_5GHZ] = &__wl_band_5ghz_a;
  ^~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_inform_single_bss’:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1981:3: error: incompatible type for argument 2 of ‘ieee80211_channel_to_frequency’
   (notif_bss_info->channel <= CH_MAX_2G_CHANNEL) ?
   ^
In file included from /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:33:0:
/usr/src/linux-headers-4.9.0-3-common/include/net/cfg80211.h:3869:5: note: expected ‘enum nl80211_band’ but argument is of type ‘struct ieee80211_channel *’
 int ieee80211_channel_to_frequency(int chan, enum nl80211_band band);
     ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:1980:7: warning: assignment makes integer from pointer without a cast [-Wint-conversion]
  freq = ieee80211_channel_to_frequency(notif_bss_info->channel,
       ^
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2013:45: error: incompatible type for argument 3 of ‘cfg80211_inform_bss’
  cbss = cfg80211_inform_bss(wiphy, channel, (const u8 *)(bi->BSSID.octet),
                                             ^
In file included from /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:33:0:
/usr/src/linux-headers-4.9.0-3-common/include/net/cfg80211.h:4450:1: note: expected ‘enum cfg80211_bss_frame_type’ but argument is of type ‘const u8 * {aka const unsigned char *}’
 cfg80211_inform_bss(struct wiphy *wiphy,
 ^~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2015:3: warning: passing argument 7 of ‘cfg80211_inform_bss’ makes integer from pointer without a cast [-Wint-conversion]
   (const u8 *)notify_ie, notify_ielen, signal, GFP_KERNEL);
   ^
In file included from /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:33:0:
/usr/src/linux-headers-4.9.0-3-common/include/net/cfg80211.h:4450:1: note: expected ‘u16 {aka short unsigned int}’ but argument is of type ‘const u8 * {aka const unsigned char *}’
 cfg80211_inform_bss(struct wiphy *wiphy,
 ^~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2015:26: warning: passing argument 8 of ‘cfg80211_inform_bss’ makes pointer from integer without a cast [-Wint-conversion]
   (const u8 *)notify_ie, notify_ielen, signal, GFP_KERNEL);
                          ^~~~~~~~~~~~
In file included from /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:33:0:
/usr/src/linux-headers-4.9.0-3-common/include/net/cfg80211.h:4450:1: note: expected ‘const u8 * {aka const unsigned char *}’ but argument is of type ‘size_t {aka long unsigned int}’
 cfg80211_inform_bss(struct wiphy *wiphy,
 ^~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2013:9: error: too few arguments to function ‘cfg80211_inform_bss’
  cbss = cfg80211_inform_bss(wiphy, channel, (const u8 *)(bi->BSSID.octet),
         ^~~~~~~~~~~~~~~~~~~
In file included from /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:33:0:
/usr/src/linux-headers-4.9.0-3-common/include/net/cfg80211.h:4450:1: note: declared here
 cfg80211_inform_bss(struct wiphy *wiphy,
 ^~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2013:7: error: assignment from incompatible pointer type [-Werror=incompatible-pointer-types]
  cbss = cfg80211_inform_bss(wiphy, channel, (const u8 *)(bi->BSSID.octet),
       ^
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_notify_connect_status’:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2050:4: error: too few arguments to function ‘cfg80211_disconnected’
    cfg80211_disconnected(ndev, 0, NULL, 0, GFP_KERNEL);
    ^~~~~~~~~~~~~~~~~~~~~
In file included from /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:33:0:
/usr/src/linux-headers-4.9.0-3-common/include/net/cfg80211.h:5074:6: note: declared here
 void cfg80211_disconnected(struct net_device *dev, u16 reason,
      ^~~~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2050:4: warning: statement with no effect [-Wunused-value]
    cfg80211_disconnected(ndev, 0, NULL, 0, GFP_KERNEL);
    ^~~~~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_ch_to_chanspec’:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2206:18: warning: comparison between pointer and integer
   if (chan->band == IEEE80211_BAND_2GHZ) {
                  ^~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2209:23: warning: comparison between pointer and integer
   else if (chan->band == IEEE80211_BAND_5GHZ) {
                       ^~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_bss_connect_done’:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2343:40: warning: passing argument 2 of ‘cfg80211_scan_done’ makes pointer from integer without a cast [-Wint-conversion]
   cfg80211_scan_done(wl->scan_request, true);
                                        ^~~~
In file included from /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:33:0:
/usr/src/linux-headers-4.9.0-3-common/include/net/cfg80211.h:4304:6: note: expected ‘struct cfg80211_scan_info *’ but argument is of type ‘int’
 void cfg80211_scan_done(struct cfg80211_scan_request *request,
      ^~~~~~~~~~~~~~~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_update_wiphybands’:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2843:15: error: array subscript is not an integer
   wiphy->bands[IEEE80211_BAND_5GHZ] = &__wl_band_5ghz_n;
               ^
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2843:3: warning: statement with no effect [-Wunused-value]
   wiphy->bands[IEEE80211_BAND_5GHZ] = &__wl_band_5ghz_n;
   ^~~~~
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_cfg80211_down’:
/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:2871:40: warning: passing argument 2 of ‘cfg80211_scan_done’ makes pointer from integer without a cast [-Wint-conversion]
   cfg80211_scan_done(wl->scan_request, true);
                                        ^~~~
In file included from /var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.c:33:0:
/usr/src/linux-headers-4.9.0-3-common/include/net/cfg80211.h:4304:6: note: expected ‘struct cfg80211_scan_info *’ but argument is of type ‘int’
 void cfg80211_scan_done(struct cfg80211_scan_request *request,
      ^~~~~~~~~~~~~~~~~~
cc1: some warnings being treated as errors
/usr/src/linux-headers-4.9.0-3-common/scripts/Makefile.build:298: polecenia dla obiektu '/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.o' nie powiodły się
make[4]: *** [/var/lib/dkms/broadcom-sta/6.30.223.248/build/src/wl/sys/wl_cfg80211_hybrid.o] Błąd 1
/usr/src/linux-headers-4.9.0-3-common/Makefile:1507: polecenia dla obiektu '_module_/var/lib/dkms/broadcom-sta/6.30.223.248/build' nie powiodły się
make[3]: *** [_module_/var/lib/dkms/broadcom-sta/6.30.223.248/build] Błąd 2
Makefile:150: polecenia dla obiektu 'sub-make' nie powiodły się
make[2]: *** [sub-make] Błąd 2
Makefile:8: polecenia dla obiektu 'all' nie powiodły się
make[1]: *** [all] Błąd 2
make[1]: Opuszczenie katalogu '/usr/src/linux-headers-4.9.0-3-amd64'
Makefile:158: polecenia dla obiektu 'all' nie powiodły się
make: *** [all] Błąd 2

arecki · 2017-08-20 22:53:10

Pokaż swoje repozytoria.

basert · 2017-08-20 22:55:05

Kod:

# 

# deb cdrom:[Debian GNU/Linux 9.1.0 _Stretch_ - Official amd64 NETINST 20170722-11:28]/ stretch main

#deb cdrom:[Debian GNU/Linux 9.1.0 _Stretch_ - Official amd64 NETINST 20170722-11:28]/ stretch main

deb http://ftp.us.debian.org/debian/ stretch main
deb-src http://ftp.us.debian.org/debian/ stretch main

deb http://security.debian.org/debian-security stretch/updates main
deb-src http://security.debian.org/debian-security stretch/updates main

# stretch-updates, previously known as 'volatile'
deb http://ftp.us.debian.org/debian/ stretch-updates main
deb-src http://ftp.us.debian.org/debian/ stretch-updates main

#moje repozytoria

# Debian 8 "Jessie"
deb http://httpredir.debian.org/debian/ jessie main contrib non-free

arecki · 2017-08-20 22:57:00

Zachaszuj ostatni wpis dla jessie, do głównego repo stretch dopisz sekcje non-free i contrib, zrób update paczek i ponownie wykonaj instalację.

Ostatnio edytowany przez arecki (2017-08-20 22:58:25)

basert · 2017-08-20 23:11:02

Poprawnie?

Kod:

# deb cdrom:[Debian GNU/Linux 9.1.0 _Stretch_ - Official amd64 NETINST 20170722$

#deb cdrom:[Debian GNU/Linux 9.1.0 _Stretch_ - Official amd64 NETINST 20170722-$

deb http://ftp.us.debian.org/debian/ stretch main
deb-src http://ftp.us.debian.org/debian/ stretch main

deb http://ftp.pl.debian.org/debian/ stretch contrib
deb-src http://ftp.pl.debian.org/debian/ stretch contrib 
deb http://ftp.pl.debian.org/debian/ stretch non-free  
deb-src http://ftp.pl.debian.org/debian/ stretch non-free  
 
deb http://security.debian.org/debian-security stretch/updates main
deb-src http://security.debian.org/debian-security stretch/updates main

# stretch-updates, previously known as 'volatile'
deb http://ftp.us.debian.org/debian/ stretch-updates main
#moje repozytoria

# Debian 8 "Jessie"
#deb http://httpredir.debian.org/debian/ jessie main contrib non-free

basert · 2017-08-20 23:12:17

Karta dodana. Niestety po połączeniu z AP nie przechodzą w sieci pakiety ICMP.

Ostatnio edytowany przez basert (2017-08-20 23:15:12)

arecki · 2017-08-20 23:15:29

Może lepiej tak:

Kod:

# deb cdrom:[Debian GNU/Linux 9.1.0 _Stretch_ - Official amd64 NETINST 20170722$

#deb cdrom:[Debian GNU/Linux 9.1.0 _Stretch_ - Official amd64 NETINST 20170722-$

#deb http://ftp.us.debian.org/debian/ stretch main
#deb-src http://ftp.us.debian.org/debian/ stretch main

deb http://ftp.pl.debian.org/debian/ stretch main contrib non-free
#deb-src http://ftp.pl.debian.org/debian/ stretch contrib 
 
deb http://security.debian.org/debian-security stretch/updates main contrib non-free
#deb-src http://security.debian.org/debian-security stretch/updates main

# stretch-updates, previously known as 'volatile'
deb http://ftp.us.debian.org/debian/ stretch-updates main contrib non-free
#moje repozytoria

# Debian 8 "Jessie"
#deb http://httpredir.debian.org/debian/ jessie main contrib non-free

arecki · 2017-08-20 23:16:24

Jak pakiety ICMP nie przechodzą to trzeba sprawdzić firewalle i ewentualnie zmienną /proc/sys/net/ipv4/icmp_echo_ignore_all

Ostatnio edytowany przez arecki (2017-08-20 23:18:45)

basert · 2017-08-20 23:18:16

Źle się wyraziłem. Po połaszeniu WLAN nie przechodzą żadne pakiety.

arecki · 2017-08-20 23:19:23

Jak to stwierdzasz?

basert · 2017-08-20 23:21:48

Nie przechodzi ICMP, nie działają strony internetowe, nie działa thunderbird.

Kod:

root@mars:/home/baser# ifconfig
eth0: flags=-28605<UP,BROADCAST,RUNNING,MULTICAST,DYNAMIC>  mtu 1500
        ether f8:a9:63:3f:a0:38  txqueuelen 1000  (Ethernet)
        RX packets 86132  bytes 78696630 (75.0 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 73234  bytes 9047312 (8.6 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 16  

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1  (Local Loopback)
        RX packets 12397  bytes 1085584 (1.0 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 12397  bytes 1085584 (1.0 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=-28605<UP,BROADCAST,RUNNING,MULTICAST,DYNAMIC>  mtu 1500
        inet 192.168.1.100  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 fe80::28e7:9aeb:1cf3:96e7  prefixlen 64  scopeid 0x20<link>
        ether f8:2f:a8:ed:6d:c9  txqueuelen 1000  (Ethernet)
        RX packets 1090  bytes 343740 (335.6 KiB)
        RX errors 0  dropped 0  overruns 0  frame 934
        TX packets 1387  bytes 233288 (227.8 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 17

Ostatnio edytowany przez basert (2017-08-20 23:23:46)

arecki · 2017-08-20 23:23:55

A ping do routera działa?

basert · 2017-08-20 23:26:02

Mam 2 routery: xDSL i LTE, ping do obu działa, lecz w WAN już nie. Przy połączeniu kablem lub z innego PC po WLAN jest ok.

Ostatnio edytowany przez basert (2017-08-20 23:26:34)

arecki · 2017-08-20 23:27:05

A ping na 8.8.8.8?

basert · 2017-08-20 23:28:41

Do DNS googla ping przechodzi poprawnie. Gdzie mogę dopatrywać się problemu?

arecki · 2017-08-20 23:30:11

W rozwiązywaniu adresów dns:

Kod:

cat /etc/resolv.conf

basert · 2017-08-20 23:32:38

Kod:

# Generated by Connection Manager
nameserver 127.0.0.1
nameserver ::1
root@mars:/home/baser#

arecki · 2017-08-20 23:34:38

Skonfiguruj sobie w tym Connection Manager (cokolwiek to jest) prawidłowe serwery DNS.

Na sam koniec, ze względu na tem misz-masz repozytoriów, warto wykonać:

Kod:

apt-get update && apt-get dist-upgrade

Ostatnio edytowany przez arecki (2017-08-20 23:37:07)

basert · 2017-08-21 00:00:45

Wszystko działa. Dziękuje za pomoc.

Time (s)	Query
0.00009	SET CHARSET latin2
0.00004	SET NAMES latin2
0.00099	SELECT u., g., o.logged FROM punbb_users AS u INNER JOIN punbb_groups AS g ON u.group_id=g.g_id LEFT JOIN punbb_online AS o ON o.ident='18.221.238.204' WHERE u.id=1
0.00077	REPLACE INTO punbb_online (user_id, ident, logged) VALUES(1, '18.221.238.204', 1732484245)
0.00046	SELECT * FROM punbb_online WHERE logged<1732483945
0.00044	SELECT topic_id FROM punbb_posts WHERE id=313521
0.00005	SELECT id FROM punbb_posts WHERE topic_id=29823 ORDER BY posted
0.00056	SELECT t.subject, t.closed, t.num_replies, t.sticky, f.id AS forum_id, f.forum_name, f.moderators, fp.post_replies, 0 FROM punbb_topics AS t INNER JOIN punbb_forums AS f ON f.id=t.forum_id LEFT JOIN punbb_forum_perms AS fp ON (fp.forum_id=f.id AND fp.group_id=3) WHERE (fp.read_forum IS NULL OR fp.read_forum=1) AND t.id=29823 AND t.moved_to IS NULL
0.00005	SELECT search_for, replace_with FROM punbb_censoring
0.00114	SELECT u.email, u.title, u.url, u.location, u.use_avatar, u.signature, u.email_setting, u.num_posts, u.registered, u.admin_note, p.id, p.poster AS username, p.poster_id, p.poster_ip, p.poster_email, p.message, p.hide_smilies, p.posted, p.edited, p.edited_by, g.g_id, g.g_user_title, o.user_id AS is_online FROM punbb_posts AS p INNER JOIN punbb_users AS u ON u.id=p.poster_id INNER JOIN punbb_groups AS g ON g.g_id=u.group_id LEFT JOIN punbb_online AS o ON (o.user_id=u.id AND o.user_id!=1 AND o.idle=0) WHERE p.topic_id=29823 ORDER BY p.id LIMIT 0,25
0.00095	UPDATE punbb_topics SET num_views=num_views+1 WHERE id=29823
Total query time: 0.00554 s

Forum Debian Users Gang

Ogłoszenie

#1 2017-08-20 22:38:51

basert - Użytkownik

Problem z instalacja karty sieciowej WLAN

Kod:

Kod:

Kod:

Kod:

Kod:

Kod:

Kod:

#2 2017-08-20 22:41:33

arecki - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

Kod:

#3 2017-08-20 22:48:27

basert - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

Kod:

#4 2017-08-20 22:53:10

arecki - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

#5 2017-08-20 22:55:05

basert - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

Kod:

#6 2017-08-20 22:57:00

arecki - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

#7 2017-08-20 23:11:02

basert - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

Kod:

#8 2017-08-20 23:12:17

basert - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

#9 2017-08-20 23:15:29

arecki - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

Kod:

#10 2017-08-20 23:16:24

arecki - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

#11 2017-08-20 23:18:16

basert - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

#12 2017-08-20 23:19:23

arecki - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

#13 2017-08-20 23:21:48

basert - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

Kod:

#14 2017-08-20 23:23:55

arecki - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

#15 2017-08-20 23:26:02

basert - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

#16 2017-08-20 23:27:05

arecki - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

#17 2017-08-20 23:28:41

basert - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

#18 2017-08-20 23:30:11

arecki - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

Kod:

#19 2017-08-20 23:32:38

basert - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

Kod:

#20 2017-08-20 23:34:38

arecki - Użytkownik

Re: Problem z instalacja karty sieciowej WLAN

Kod:

#21 2017-08-21 00:00:45

basert - Użytkownik