Nie jesteś zalogowany.
Jeśli nie posiadasz konta, zarejestruj je już teraz! Pozwoli Ci ono w pełni korzystać z naszego serwisu. Spamerom dziękujemy!
Prosimy o pomoc dla małej Julki — przekaż 1% podatku na Fundacji Dzieciom zdazyć z Pomocą.
Więcej informacji na dug.net.pl/pomagamy/.
Hej,
mam nexusa 3000 "ożenionego" z kartą LR-LINK 2x10G na debianie 8.
Wszystko było dobrze do czasu. Zaobserwowałem że na cisco mam dużo RX paused. Zrobiony LACP/bonding 2x10G
bitlan@BGP-1:~$ [b]cat /proc/net/bonding/bond0[/b]
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer3+4 (1)
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
Active Aggregator Info:
Aggregator ID: 2
Number of ports: 2
Actor Key: 33
Partner Key: 32768
Partner Mac Address: xxxxxxxxxxx:be:7c
Slave Interface: eth2
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 2
Permanent HW addr: xxxxxxxxxxx:54:eb
Aggregator ID: 2
Slave queue ID: 0
Slave Interface: eth3
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 3
Permanent HW addr: xxxxxxxxxxx:54:ed
Aggregator ID: 2
Slave queue ID: 0
bitlan@BGP-1:~$
root@BGP-1:~# [b]ethtool eth2[/b]
Settings for eth2:
Supported ports: [ FIBRE ]
Supported link modes: 10000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Advertised link modes: 10000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: external
Auto-negotiation: off
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
root@BGP-1:~# [b]ethtool eth3[/b]
Settings for eth3:
Supported ports: [ FIBRE ]
Supported link modes: 10000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Advertised link modes: 10000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: external
Auto-negotiation: off
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
root@BGP-1:~# [b]ethtool -a eth2[/b]
Pause parameters for eth2:
Autonegotiate: off
RX: on
TX: on
root@BGP-1:~# [b]ethtool -a eth3[/b]
Pause parameters for eth3:
Autonegotiate: off
RX: on
TX: on
root@BGP-1:~#
root@BGP-1:~# [b]ethtool -c eth3[/b]
Coalesce parameters for eth3:
Adaptive RX: off TX: off
stats-block-usecs: 0
sample-interval: 0
pkt-rate-low: 0
pkt-rate-high: 0
rx-usecs: 512
rx-frames: 0
rx-usecs-irq: 0
rx-frames-irq: 0
tx-usecs: 0
tx-frames: 0
tx-usecs-irq: 0
tx-frames-irq: 256
rx-usecs-low: 0
rx-frame-low: 0
tx-usecs-low: 0
tx-frame-low: 0
rx-usecs-high: 0
rx-frame-high: 0
tx-usecs-high: 0
tx-frame-high: 0
root@BGP-1:~# [b]ethtool -c eth2[/b]
Coalesce parameters for eth2:
Adaptive RX: off TX: off
stats-block-usecs: 0
sample-interval: 0
pkt-rate-low: 0
pkt-rate-high: 0
rx-usecs: 512
rx-frames: 0
rx-usecs-irq: 0
rx-frames-irq: 0
tx-usecs: 0
tx-frames: 0
tx-usecs-irq: 0
tx-frames-irq: 256
rx-usecs-low: 0
rx-frame-low: 0
tx-usecs-low: 0
tx-frame-low: 0
rx-usecs-high: 0
rx-frame-high: 0
tx-usecs-high: 0
tx-frame-high: 0
root@BGP-1:~#
root@BGP-1:~# [b]ethtool -i eth3[/b]
driver: ixgbe
version: 4.5.4
firmware-version: 0x2b2c0001
bus-info: 0000:1a:00.1
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: yes
root@BGP-1:~#[/quote]
mniej więcej zaczęło się tak dziać (przy okazji "zacina" ładowanie stron itp. )jak ruch wzrósł >1G, co ciekawsze mam zrobioną też agregacje na mikrotiku 2x1G i tam nie spotkałem się z czymś takim.
Jakieś sugestie? podpowiedź w którym kierunku szukać?
Offline
| Time (s) | Query |
|---|---|
| 0.00010 | SET CHARSET latin2 |
| 0.00004 | SET NAMES latin2 |
| 0.00110 | SELECT u.*, g.*, o.logged FROM punbb_users AS u INNER JOIN punbb_groups AS g ON u.group_id=g.g_id LEFT JOIN punbb_online AS o ON o.ident='3.144.46.90' WHERE u.id=1 |
| 0.00065 | REPLACE INTO punbb_online (user_id, ident, logged) VALUES(1, '3.144.46.90', 1732316226) |
| 0.00038 | SELECT * FROM punbb_online WHERE logged<1732315926 |
| 0.00082 | SELECT topic_id FROM punbb_posts WHERE id=313562 |
| 0.00074 | SELECT id FROM punbb_posts WHERE topic_id=29830 ORDER BY posted |
| 0.00059 | SELECT t.subject, t.closed, t.num_replies, t.sticky, f.id AS forum_id, f.forum_name, f.moderators, fp.post_replies, 0 FROM punbb_topics AS t INNER JOIN punbb_forums AS f ON f.id=t.forum_id LEFT JOIN punbb_forum_perms AS fp ON (fp.forum_id=f.id AND fp.group_id=3) WHERE (fp.read_forum IS NULL OR fp.read_forum=1) AND t.id=29830 AND t.moved_to IS NULL |
| 0.00006 | SELECT search_for, replace_with FROM punbb_censoring |
| 0.00096 | SELECT u.email, u.title, u.url, u.location, u.use_avatar, u.signature, u.email_setting, u.num_posts, u.registered, u.admin_note, p.id, p.poster AS username, p.poster_id, p.poster_ip, p.poster_email, p.message, p.hide_smilies, p.posted, p.edited, p.edited_by, g.g_id, g.g_user_title, o.user_id AS is_online FROM punbb_posts AS p INNER JOIN punbb_users AS u ON u.id=p.poster_id INNER JOIN punbb_groups AS g ON g.g_id=u.group_id LEFT JOIN punbb_online AS o ON (o.user_id=u.id AND o.user_id!=1 AND o.idle=0) WHERE p.topic_id=29830 ORDER BY p.id LIMIT 0,25 |
| 0.00073 | UPDATE punbb_topics SET num_views=num_views+1 WHERE id=29830 |
| Total query time: 0.00617 s | |