Forum Debian Users Gang

morfik · 2016-05-31 17:35:02

No ale wskaż też ten dysk co masz z nim problem. xD

milik · 2016-05-31 20:55:11

Naturalnie :D

Kod:

root@irin:/home/michal# hdparm -I -i /dev/sdb

/dev/sdb:
 HDIO_GET_IDENTITY failed: Invalid argument

ATA device, with non-removable media
    Model Number:       ST1000LM025 HN-M101ABB                  
    Serial Number:      G3913G941D7DB3      
    Firmware Revision:  2BA30003
    Transport:          Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
    Used: unknown (minor revision code 0x0028) 
    Supported: 8 7 6 5 
    Likely used: 8
Configuration:
    Logical        max    current
    cylinders    16383    16383
    heads        16    16
    sectors/track    63    63
    --
    CHS current addressable sectors:   16514064
    LBA    user addressable sectors:  268435455
    LBA48  user addressable sectors: 1953525168
    Logical  Sector size:                   512 bytes
    Physical Sector size:                  4096 bytes
    Logical Sector-0 offset:                  0 bytes
    device size with M = 1024*1024:      953869 MBytes
    device size with M = 1000*1000:     1000204 MBytes (1000 GB)
    cache/buffer size  = 8192 KBytes
    Form Factor: 2.5 inch
    Nominal Media Rotation Rate: 5400
Capabilities:
    LBA, IORDY(can be disabled)
    Queue depth: 32
    Standby timer values: spec'd by Standard, no device specific minimum
    R/W multiple sector transfer: Max = 16    Current = ?
    Advanced power management level: disabled
    Recommended acoustic management value: 254, current value: 0
    DMA: mdma0 mdma1 *mdma2 udma0 udma1 udma2 udma3 udma4 udma5 udma6 
         Cycle time: min=120ns recommended=120ns
    PIO: pio0 pio1 pio2 pio3 pio4 
         Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
    Enabled    Supported:
       *    SMART feature set
            Security Mode feature set
       *    Power Management feature set
       *    Write cache
       *    Look-ahead
       *    Host Protected Area feature set
       *    WRITE_BUFFER command
       *    READ_BUFFER command
       *    NOP cmd
       *    DOWNLOAD_MICROCODE
            Advanced Power Management feature set
            Power-Up In Standby feature set
       *    SET_FEATURES required to spinup after power up
            SET_MAX security extension
            Automatic Acoustic Management feature set
       *    48-bit Address feature set
       *    Device Configuration Overlay feature set
       *    Mandatory FLUSH_CACHE
       *    FLUSH_CACHE_EXT
       *    SMART error logging
       *    SMART self-test
       *    General Purpose Logging feature set
       *    64-bit World wide name
       *    IDLE_IMMEDIATE with UNLOAD
       *    WRITE_UNCORRECTABLE_EXT command
       *    {READ,WRITE}_DMA_EXT_GPL commands
       *    Segmented DOWNLOAD_MICROCODE
       *    Gen1 signaling speed (1.5Gb/s)
       *    Gen2 signaling speed (3.0Gb/s)
       *    Native Command Queueing (NCQ)
       *    Phy event counters
       *    Idle-Unload when NCQ is active
       *    NCQ priority information
            DMA Setup Auto-Activate optimization
            Device-initiated interface power management
            Software settings preservation
       *    SMART Command Transport (SCT) feature set
       *    SCT Read/Write Long (AC1), obsolete
       *    SCT Write Same (AC2)
       *    SCT Error Recovery Control (AC3)
       *    SCT Features Control (AC4)
       *    SCT Data Tables (AC5)
Security: 
    Master password revision code = 65534
        supported
    not    enabled
    not    locked
    not    frozen
    not    expired: security count
        supported: enhanced erase
    212min for SECURITY ERASE UNIT. 212min for ENHANCED SECURITY ERASE UNIT. 
Logical Unit WWN Device Identifier: 0000000000000000
    NAA        : 0
    IEEE OUI    : 000000
    Unique ID    : 000000000
Checksum: correct
root@irin:/home/michal#

morfik · 2016-05-31 21:42:50

A co mówi:

Kod:

# smartctl --all /dev/sdb

rychu · 2016-05-31 22:27:09

raczej nie próbuj otwierać obudowy dysku, jak ci radzą niektórzy niedoświadczeni użyszkodnicy, bo możesz go potem nie złożyć. wg tego co mówi [b]hdparm[/b] to jest prawdziwy dysk, zresztą możesz sprawdzić to organoleptycznie: wrzuć mu duże obciążenie (np. [b]cat /dev/sdb > /dev/null[/b] - przeczyta całą zawartość dysku i nic z tym nie zrobi) i weź dysk do ręki. jeżeli czujesz delikatne drgania, słyszysz cichy szum lub obracając dysk wokół dowolnej osi wyczuwasz delikatny opór, to jest to prawdziwy dysk talerzowy.

tak jak pisał [b]qluk[/b] prawdopodobnie bawiłeś się ghostem (taki soft do robienia backupów) i coś nie wyszło. twoje podejście (skopiować pliki z dysku i sformatować) jest słuszne.

mówiłeś, że możesz oglądać zawartość dysku w [b]mc[/b], czy możesz za jego pomocą przekopiować swoje pliki? albo poleceniem [b]cp[/b] w konsoli?

milik · 2016-06-01 19:02:01

Kod:

root@irin:/home/michal# smartctl --all /dev/sdb
smartctl 6.4 2014-10-07 r4002 [i686-linux-3.16.0-4-686-pae] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Samsung SpinPoint M8U (USB)
Device Model:     ST1000LM025 HN-M101ABB
Serial Number:    G3913G941D7DB3
LU WWN Device Id: 0 000000 000000000
Firmware Version: 2BA30003
User Capacity:    1,000,204,886,016 bytes [1,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Wed Jun  1 18:58:01 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)    Offline data collection activity
                    was never started.
                    Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever 
                    been run.
Total time to complete Offline 
data collection:         (13200) seconds.
Offline data collection
capabilities:              (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine 
recommended polling time:      (   2) minutes.
Extended self-test routine
recommended polling time:      ( 220) minutes.
SCT capabilities:            (0x003f)    SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   100   100   051    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0026   252   252   000    Old_age   Always       -       0
  3 Spin_Up_Time            0x0023   089   089   025    Pre-fail  Always       -       3462
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       80
  5 Reallocated_Sector_Ct   0x0033   252   252   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   252   252   051    Old_age   Always       -       0
  8 Seek_Time_Performance   0x0024   252   252   015    Old_age   Offline      -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       43
 10 Spin_Retry_Count        0x0032   252   252   051    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   252   252   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       48
191 G-Sense_Error_Rate      0x0022   252   252   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0022   100   100   000    Old_age   Always       -       15
194 Temperature_Celsius     0x0002   064   057   000    Old_age   Always       -       27 (Min/Max 18/44)
195 Hardware_ECC_Recovered  0x003a   100   100   000    Old_age   Always       -       0
196 Reallocated_Event_Count 0x0032   252   252   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   252   252   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   252   252   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0036   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x002a   100   100   000    Old_age   Always       -       0
223 Load_Retry_Count        0x0032   252   252   000    Old_age   Always       -       0
225 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       1288

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Completed [00% left] (0-65535)
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@irin:/home/michal#

Problem dotyczył tylko tego jednegopliku zrobionego Ghostem, to jest obraz partycji Windowsowej z komputera żony, nie mam pojęcia dlaczego coś mu się stało. W mc mogę swobodnie kopiować wszystkie pliki oprócz tego obrazu ( skasować też go nie mogłem). Obecnie dysk jest po formacie, na system plików NTFS, póki co działa.
Skanowałem cały dysk pod kontem badsektorów i pokazało, że takowych nie znaleziono. Zobaczymy jak długo podziała. Otwierać oczywiście nie zamiaruję ;)

morfik · 2016-06-01 19:26:21

Dysk jest sprawny. Także problem jest z samym plikiem.

milik · 2017-08-23 21:02:20

Czy jest jakiś sposób na usunięcie tego pliku uszkodzonego? Poprzednim razem skopiowałem całą zawartość, oczywiście oprócz uszkodzonego pliku na drugi dysk i zrobiłem formata, teraz nie mam takiej możliwości i może ma ktoś pomysł jak usunąć ten felerny plik?

wikingagressor · 2017-08-24 00:46:11

[quote=milik]Czy jest jakiś sposób na usunięcie tego pliku uszkodzonego? Poprzednim razem skopiowałem całą zawartość, oczywiście oprócz uszkodzonego pliku na drugi dysk i zrobiłem formata, teraz nie mam takiej możliwości i może ma ktoś pomysł jak usunąć ten felerny plik?[/quote]
A nie mozesz w konsoli usunac za pomoca komendy [b]rm[/b] ?

milik · 2017-08-24 07:38:17

No właśnie, że nie. Próbowałem już i wyskakuje taki błąd:

Kod:

root@irin:/media/milik/SAMSUNG# rm -f 1.\ Mała\ syrenka\ \(1989r\).avi 
rm: nie można usunąć '1. Mała syrenka (1989r).avi': Błąd wejścia/wyjścia
root@irin:/media/milik/SAMSUNG#

urbinek · 2017-08-24 09:04:36

zaraz po próbie usunięcia zrób

Kod:

 dmesg | tail -n 100

milik · 2017-08-24 12:14:11

Kod:

root@irin:/media/milik/SAMSUNG# rm -f 1.\ Mała\ syrenka\ \(1989r\).avi 
rm: nie można usunąć '1. Mała syrenka (1989r).avi': Błąd wejścia/wyjścia
root@irin:/media/milik/SAMSUNG# dmesg | tail -n 100
[  541.269934] vgaarb: this pci device is not a vga device
[  541.318492] vgaarb: this pci device is not a vga device
[  541.348455] vgaarb: this pci device is not a vga device
[  551.236831] vgaarb: this pci device is not a vga device
[  551.276483] vgaarb: this pci device is not a vga device
[  551.305096] vgaarb: this pci device is not a vga device
[  556.741827] vgaarb: this pci device is not a vga device
[  556.778784] vgaarb: this pci device is not a vga device
[  556.792035] vgaarb: this pci device is not a vga device
[  566.689067] vgaarb: this pci device is not a vga device
[  566.707556] vgaarb: this pci device is not a vga device
[  566.756963] vgaarb: this pci device is not a vga device
[  576.741553] vgaarb: this pci device is not a vga device
[  576.794602] vgaarb: this pci device is not a vga device
[  576.805971] vgaarb: this pci device is not a vga device
[  586.956095] vgaarb: this pci device is not a vga device
[  587.041535] vgaarb: this pci device is not a vga device
[  587.077138] vgaarb: this pci device is not a vga device
[  597.020047] vgaarb: this pci device is not a vga device
[  597.103641] vgaarb: this pci device is not a vga device
[  597.141548] vgaarb: this pci device is not a vga device
[  606.957587] vgaarb: this pci device is not a vga device
[  607.008521] vgaarb: this pci device is not a vga device
[  607.032204] vgaarb: this pci device is not a vga device
[  699.981385] vgaarb: this pci device is not a vga device
[  699.991669] vgaarb: this pci device is not a vga device
[  700.027409] vgaarb: this pci device is not a vga device
[  710.439975] vgaarb: this pci device is not a vga device
[  710.469816] vgaarb: this pci device is not a vga device
[  710.496474] vgaarb: this pci device is not a vga device
[  720.546903] vgaarb: this pci device is not a vga device
[  720.613432] vgaarb: this pci device is not a vga device
[  720.647900] vgaarb: this pci device is not a vga device
[  730.595743] vgaarb: this pci device is not a vga device
[  730.690758] vgaarb: this pci device is not a vga device
[  730.738191] vgaarb: this pci device is not a vga device
[  740.607731] vgaarb: this pci device is not a vga device
[  740.627670] vgaarb: this pci device is not a vga device
[  740.653407] vgaarb: this pci device is not a vga device
[  750.516903] vgaarb: this pci device is not a vga device
[  750.553427] vgaarb: this pci device is not a vga device
[  750.577805] vgaarb: this pci device is not a vga device
[  760.735499] vgaarb: this pci device is not a vga device
[  760.785163] vgaarb: this pci device is not a vga device
[  760.808589] vgaarb: this pci device is not a vga device
[  770.610294] vgaarb: this pci device is not a vga device
[  770.658523] vgaarb: this pci device is not a vga device
[  770.725621] vgaarb: this pci device is not a vga device
[  780.646863] vgaarb: this pci device is not a vga device
[  780.679498] vgaarb: this pci device is not a vga device
[  780.705805] vgaarb: this pci device is not a vga device
[  790.643693] vgaarb: this pci device is not a vga device
[  790.716757] vgaarb: this pci device is not a vga device
[  790.734507] vgaarb: this pci device is not a vga device
[  934.722208] perf: interrupt took too long (3915 > 3910), lowering kernel.perf_event_max_sample_rate to 51000
[ 5845.313201] vgaarb: this pci device is not a vga device
[ 5851.111774] vgaarb: this pci device is not a vga device
[ 5851.743979] vgaarb: this pci device is not a vga device
[ 5851.746000] nvidia-modeset: Allocated GPU:0 (GPU-42e7166b-90c5-deb3-f7a8-6815157d63f0) @ PCI:0000:04:00.0
[ 5851.746199] nvidia-modeset: Freed GPU:0 (GPU-42e7166b-90c5-deb3-f7a8-6815157d63f0) @ PCI:0000:04:00.0
[ 5851.748552] vgaarb: this pci device is not a vga device
[ 6452.765370] vgaarb: this pci device is not a vga device
[39746.889916] vgaarb: this pci device is not a vga device
[39753.724123] vgaarb: this pci device is not a vga device
[39798.596546] usb 3-2: new SuperSpeed USB device number 2 using xhci_hcd
[39798.617324] usb 3-2: New USB device found, idVendor=04e8, idProduct=61b6
[39798.617327] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[39798.617328] usb 3-2: Product: Samsung M3 Portable
[39798.617329] usb 3-2: Manufacturer: Samsung M3 Portable
[39798.617330] usb 3-2: SerialNumber: C0057DFB150000A1
[39798.638710] usbcore: registered new interface driver usb-storage
[39798.641943] scsi host2: uas
[39798.643852] usbcore: registered new interface driver uas
[39798.644315] scsi 2:0:0:0: Direct-Access     Samsung  M3 Portable      1306 PQ: 0 ANSI: 6
[39798.689348] sd 2:0:0:0: Attached scsi generic sg2 type 0
[39800.593751] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[39800.593753] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[39800.594264] sd 2:0:0:0: [sdb] Write Protect is off
[39800.594266] sd 2:0:0:0: [sdb] Mode Sense: 53 00 00 08
[39800.594544] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[39800.608228]  sdb: sdb1
[39800.609675] sd 2:0:0:0: [sdb] Attached SCSI disk
[40555.918084] wlp3s0: AP 10:fe:ed:c7:f0:10 changed bandwidth, new config is 2437 MHz, width 1 (2437/0 MHz)
[40556.941864] wlp3s0: AP 10:fe:ed:c7:f0:10 changed bandwidth, new config is 2437 MHz, width 2 (2427/0 MHz)
[40561.286846] vgaarb: this pci device is not a vga device
[40567.894643] vgaarb: this pci device is not a vga device
[40568.489080] vgaarb: this pci device is not a vga device
[40568.491347] nvidia-modeset: Allocated GPU:0 (GPU-42e7166b-90c5-deb3-f7a8-6815157d63f0) @ PCI:0000:04:00.0
[40568.492023] nvidia-modeset: Freed GPU:0 (GPU-42e7166b-90c5-deb3-f7a8-6815157d63f0) @ PCI:0000:04:00.0
[40568.494469] vgaarb: this pci device is not a vga device
[40702.956804] wlp3s0: AP 10:fe:ed:c7:f0:10 changed bandwidth, new config is 2437 MHz, width 1 (2437/0 MHz)
[40703.878353] wlp3s0: AP 10:fe:ed:c7:f0:10 changed bandwidth, new config is 2437 MHz, width 2 (2427/0 MHz)
[40704.902292] wlp3s0: AP 10:fe:ed:c7:f0:10 changed bandwidth, new config is 2437 MHz, width 1 (2437/0 MHz)
[40705.927307] wlp3s0: AP 10:fe:ed:c7:f0:10 changed bandwidth, new config is 2437 MHz, width 2 (2427/0 MHz)
[40707.974312] wlp3s0: AP 10:fe:ed:c7:f0:10 changed bandwidth, new config is 2437 MHz, width 1 (2437/0 MHz)
[40709.920553] wlp3s0: AP 10:fe:ed:c7:f0:10 changed bandwidth, new config is 2437 MHz, width 2 (2427/0 MHz)
[40835.968367] wlp3s0: AP 10:fe:ed:c7:f0:10 changed bandwidth, new config is 2437 MHz, width 1 (2437/0 MHz)
[40836.889691] wlp3s0: AP 10:fe:ed:c7:f0:10 changed bandwidth, new config is 2437 MHz, width 2 (2427/0 MHz)
[41169.384656] vgaarb: this pci device is not a vga device
[55295.507525] vgaarb: this pci device is not a vga device
root@irin:/media/milik/SAMSUNG#

urbinek · 2017-08-24 12:21:30

Dysk nie raportuje żadnych błędów

Kod:

[39798.596546] usb 3-2: new SuperSpeed USB device number 2 using xhci_hcd
[39798.617324] usb 3-2: New USB device found, idVendor=04e8, idProduct=61b6
[39798.617327] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[39798.617328] usb 3-2: Product: Samsung M3 Portable
[39798.617329] usb 3-2: Manufacturer: Samsung M3 Portable
[39798.617330] usb 3-2: SerialNumber: C0057DFB150000A1
[39798.638710] usbcore: registered new interface driver usb-storage
[39798.641943] scsi host2: uas
[39798.643852] usbcore: registered new interface driver uas
[39798.644315] scsi 2:0:0:0: Direct-Access     Samsung  M3 Portable      1306 PQ: 0 ANSI: 6
[39798.689348] sd 2:0:0:0: Attached scsi generic sg2 type 0
[39800.593751] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[39800.593753] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[39800.594264] sd 2:0:0:0: [sdb] Write Protect is off
[39800.594266] sd 2:0:0:0: [sdb] Mode Sense: 53 00 00 08
[39800.594544] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[39800.608228]  sdb: sdb1
[39800.609675] sd 2:0:0:0: [sdb] Attached SCSI disk

Ihmo uszkodzony system plików. Najlepiej wykonać format a jak bardzo ci się nie chce to możesz zrobić jakiś check disk.

Pod linuksem średnio - https://askubuntu.com/questions/783324/checking-a-ntfs-drive-with-linux

Najlepiej podłączyć to pod Windowsa i wyczyścić.

p.s. Jaki system stworzył tą partycję? Wersja NTFS nie koniecznie będzie w pełni kompatybilna z linuksem.

milik · 2017-08-24 12:53:01

Winda chyba stworzyła tą partycję. Generalnie to nie mam na co zgrać tych danych żeby zrobić format, więc myślałem, że prościej będzie usunąć tą durną bajkę. Ale widać, że chyba nie jest to możliwe.

Bodzio · 2017-08-24 13:22:02

A tak nie da rady ?

shred -n 5 -vz <nazwa_pliku>

milik · 2017-08-24 13:38:48

To samo... :(

Kod:

root@irin:/media/milik/SAMSUNG# shred -n 5 -vz 1.\ Mała\ syrenka\ \(1989r\).avi shred: '1. Mała syrenka (1989r).avi': błąd przy otwieraniu do zapisu: Błąd wejścia/wyjścia
root@irin:/media/milik/SAMSUNG# shred -n 5 -vz *.avi 
shred: '1. Mała syrenka (1989r).avi': błąd przy otwieraniu do zapisu: Błąd wejścia/wyjścia
root@irin:/media/milik/SAMSUNG#

wikingagressor · 2017-08-24 15:28:26

sprobuj w gparted sprawdzic/naprawic partycje, jak nie o format wszystkiego i po problemie ;)

Time (s)	Query
0.00006	SET CHARSET latin2
0.00003	SET NAMES latin2
0.00039	SELECT u., g., o.logged FROM punbb_users AS u INNER JOIN punbb_groups AS g ON u.group_id=g.g_id LEFT JOIN punbb_online AS o ON o.ident='3.138.126.124' WHERE u.id=1
0.00079	REPLACE INTO punbb_online (user_id, ident, logged) VALUES(1, '3.138.126.124', 1732476074)
0.00021	SELECT * FROM punbb_online WHERE logged<1732475774
0.00060	SELECT topic_id FROM punbb_posts WHERE id=313665
0.00007	SELECT id FROM punbb_posts WHERE topic_id=28610 ORDER BY posted
0.00056	SELECT t.subject, t.closed, t.num_replies, t.sticky, f.id AS forum_id, f.forum_name, f.moderators, fp.post_replies, 0 FROM punbb_topics AS t INNER JOIN punbb_forums AS f ON f.id=t.forum_id LEFT JOIN punbb_forum_perms AS fp ON (fp.forum_id=f.id AND fp.group_id=3) WHERE (fp.read_forum IS NULL OR fp.read_forum=1) AND t.id=28610 AND t.moved_to IS NULL
0.00005	SELECT search_for, replace_with FROM punbb_censoring
0.00308	SELECT u.email, u.title, u.url, u.location, u.use_avatar, u.signature, u.email_setting, u.num_posts, u.registered, u.admin_note, p.id, p.poster AS username, p.poster_id, p.poster_ip, p.poster_email, p.message, p.hide_smilies, p.posted, p.edited, p.edited_by, g.g_id, g.g_user_title, o.user_id AS is_online FROM punbb_posts AS p INNER JOIN punbb_users AS u ON u.id=p.poster_id INNER JOIN punbb_groups AS g ON g.g_id=u.group_id LEFT JOIN punbb_online AS o ON (o.user_id=u.id AND o.user_id!=1 AND o.idle=0) WHERE p.topic_id=28610 ORDER BY p.id LIMIT 25,25
0.00076	UPDATE punbb_topics SET num_views=num_views+1 WHERE id=28610
Total query time: 0.0066 s

Forum Debian Users Gang

Ogłoszenie

#26 2016-05-31 17:35:02

morfik - Cenzor wirtualnego świata

Re: Dysk zewnętrzny Samsung

#27 2016-05-31 20:55:11

milik - Użytkownik

Re: Dysk zewnętrzny Samsung

Kod:

#28 2016-05-31 21:42:50

morfik - Cenzor wirtualnego świata

Re: Dysk zewnętrzny Samsung

Kod:

#29 2016-05-31 22:27:09

rychu - elektryk dyżurny

Re: Dysk zewnętrzny Samsung

#30 2016-06-01 19:02:01

milik - Użytkownik

Re: Dysk zewnętrzny Samsung

Kod:

#31 2016-06-01 19:26:21

morfik - Cenzor wirtualnego świata

Re: Dysk zewnętrzny Samsung

#32 2017-08-23 21:02:20

milik - Użytkownik

Re: Dysk zewnętrzny Samsung

#33 2017-08-24 00:46:11

wikingagressor - Użytkownik

Re: Dysk zewnętrzny Samsung

#34 2017-08-24 07:38:17

milik - Użytkownik

Re: Dysk zewnętrzny Samsung

Kod:

#35 2017-08-24 09:04:36

urbinek - Użytkownik

Re: Dysk zewnętrzny Samsung

Kod:

#36 2017-08-24 12:14:11

milik - Użytkownik

Re: Dysk zewnętrzny Samsung

Kod:

#37 2017-08-24 12:21:30

urbinek - Użytkownik

Re: Dysk zewnętrzny Samsung

Kod:

#38 2017-08-24 12:53:01

milik - Użytkownik

Re: Dysk zewnętrzny Samsung

#39 2017-08-24 13:22:02

Bodzio - Ojciec Założyciel

Re: Dysk zewnętrzny Samsung

#40 2017-08-24 13:38:48

milik - Użytkownik

Re: Dysk zewnętrzny Samsung

Kod:

#41 2017-08-24 15:28:26

wikingagressor - Użytkownik

Re: Dysk zewnętrzny Samsung

Stopka forum

Informacje debugowania