Forum Debian Users Gang

Rozdzielczość jest 1152x864, czyli taka, jaką miałem wcześniej na 17'' CRT :(

Z palca wpisałem. A jak się nazywa ten pakiet do X-ów, by go zrekonfigurować przez dpkg-reconfigure? [b]xorg.conf[/b] jest taki:

(...)


# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

#    Identifier  "Samsung SyncMaster 753DF"
    Identifier  "LG L227WT-PF"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.

#    HorizSync   30-70
    HorizSync   30-83

#    HorizSync    31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync    15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.

#    VertRefresh 50-160
    VertRefresh 56-75
       
# ModeLine "1680x1050" 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync +vsync
# ModeLine "1680x1050b" 146.2 1680 1784 1960 2240 1050 1053 1059 1089 +hsync +vsync
Modeline "1680x1050"  147.14  1680 1784 1968 2256  1050 1051 1054 1087

EndSection

# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier    "Standard VGA"
    VendorName    "Unknown"
    BoardName    "Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset    "generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver     "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.

#    BusID      "PCI:0:10:0"

#    VideoRam    256

#    Clocks    25.2 28.3

EndSection

# Device configured by xorgconfig:

Section "Device"
#    Identifier  "Riva TNT2"
    Identifier  "GeForce4 MX 440"
    Driver      "nv"
#    VideoRam    32768
    VideoRam    65536
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
#    Device      "Riva TNT2"
         Device "GeForce4 MX 440"
#    Monitor     "Samsung SyncMaster 753DF"
         Monitor "LG L227WT-PF"
       
    DefaultDepth 24

    Subsection "Display"
        Depth       8
        Modes       "1680x1050"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1680x1050"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1680x1050"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
#    Mode 0666
# EndSection[/quote]

Ostatnio edytowany przez Blackhole (2008-05-08 18:24:44)

---

Ściskam prawicę, Jacek

[url]http://doscniewoli.pl[/url] — [b]Poznaj prawdę o pieniądzach[/b]
[url]http://www.youtube.com/watch?v=BlhFK2Gc1Nw[/url] — cz. I